rockbox/manual/configure_rockbox/main.tex
Martin Arver a1d0acb243 Patch #4910 by Michael DiFebbo. More additions and updates to chapter Configure Rockbox.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@9234 a1c6a512-1295-4272-9138-f99709370657
2006-03-24 17:09:15 +00:00

475 lines
40 KiB
TeX

\chapter{Configuring Rockbox}
\label{ref:configure_rockbox}
\section{Sound Settings}
\begin{center}
\includegraphics[width=4cm]{configure_rockbox/images/ss-sound-settings-\genericimg.png}
\end{center}
This menu offers a selection of sound properties you may change to improve your sound experience.
\begin{itemize}
\item \textbf{Volume}
This control adjusts the volume of your music. Like most professional audio gear and many consumer audio products, Rockbox uses a decibel scale where 0 dB is a reference that indicates the maximum volume that the \dap can produce without distortion (clipping). Because the volume control is basically a comparison of the volume level you set to a reference volume of 0 dB.
\opt{player}{ Volume can be adjusted from a minimum of -78 dB to a maximum of +18 dB.}
\opt{recorder,recorderv2fm,ondio}{ Volume can be adjusted from a minimum of -100 dB to a maximum of +12 dB.}
\opt{h1xx,h300}{ Volume can be adjusted from a minimum of -84 dB to a maximum of 0 dB.}
\opt{ipodnano}{ Volume can be adjusted from a minimum of -72 dB to a maximum of +6 dB.}
\opt{ipodvideo}{ Volume can be adjusted from a minimum of -57 dB to a maximum of +6 dB.}
\opt{ipodcolor}{ Volume can be adjusted from a minimum of -?? dB to a maximum of +?? dB.}
\item \textbf{Bass}
\opt{player,recorder,recorderv2fm,ondio}{This emphasises or suppresses the lower (bass) sounds in the track. 0 means that bass sounds are unaltered (flat response).}
\opt{h1xx,h300}{The Bass setting can be used to increase (but not decrease) frequencies below 300Hz. Bass boost can be set from 0 to 24 dB in increments of 2 dB. A setting of 0 means that low frequencies are unaltered (flat response).}
\opt{ipodnano,ipodcolor,ipodvideo}{TODO - platform specific description.}
\item \textbf{Treble}
\opt{player,recorder,recorderv2fm,ondio}{This emphasises or suppresses the higher (treble) sounds in the track. 0 means that treble sounds are unaltered (flat response).}
\opt{h1xx,h300}{The Treble setting can be used to increase (but not decrease) frequencies above 1.5kHz. Treble boost can be set from 0 to 6 dB in increments of 2 dB. A setting of 0 means that high frequencies are unaltered (flat response).}
\opt{ipodnano,ipodcolor,ipodvideo}{TODO - platform specific description.}
\item \textbf{Balance}
How much of the volume is generated by the left or right channel of the sound. The default, 0, means that the left and right outputs are equal in volume. Negative numbers increase the volume of the left channel relative to the right, positive numbers increase the volume of the right channel relative to the left.
\item \textbf{Channels}
A stereo audio signal consists of two channels, left and right. The channels function controls how much of the left channel signal is mixed into the right channel signal, and vice versa.
\opt{MASCODEC}{This option controls the on{}-board mixing facilities of the \dap.}
\opt{SWCODEC}{This option controls the mixing facilities of the \dap.} Available options are:
\begin{itemize}
\item \textbf{Mono Left: }Plays the left channel in both stereo channels.
\item \textbf{Mono Right:} Plays the right channel in both stereo channels.
\item \textbf{Mono:} Mix both channels down to mono and send the mixed signal
back to both.
\item \textbf{Stereo:} Do not mix the signal
\item \textbf{Stereo Narrow: }Mixes small amounts of the opposite channel into
the left and right channels, thus making the sound seem closer
together.
\item \textbf{Stereo Wide:} Elements of one channel that are present in the
opposite channel are removed from the latter. This results in the
sound seeming further apart.
\item \textbf{Karaoke:} Removes all sound that is the same in both channels.
Since most vocals are recorded in this way to make the artist sound
central, this often (but not always) has the effect of removing the
voice track from a song.
\end{itemize}
\opt{recorder,recorderv2fm}{
\item \textbf{Loudness}
Loudness is an effect which emphasises bass and treble. This makes the track seem louder by amplifying the frequencies that the human ear finds hard to hear. Frequencies in the vocal range are unaffected, since the human ear picks these up very easily.
}
\opt{recorder,recorderv2fm}{
\item \textbf{Auto Volume}
Auto volume is a feature that automatically lowers the volume on loud parts, and then slowly restores the volume to the previous level over a time interval. That time interval is configurable here. Short values like 20ms are useful for ensuring a constant volume for in car use and other applications where background noise makes a constant loudness desirable. A longer timeout means that the change in volume back to the previous level will be smoother, so there will be less sharp changes in volume level.
}
\opt{recorder,recorderv2fm}{
\item \textbf{Super Bass}
This setting changes the threshold at which bass frequencies are affected by the \textbf{Loudness} setting, making the sound of drums and bass guitar louder in comparison to the rest of the track. This setting only has an effect if \textbf{Loudness} is set to a value larger than 0dB.
}
\opt{recorder,recorderv2fm}{
\item \textbf{MDB {}- Micronas Dynamic Bass}
The rest of the parameters on this menu relate to the Micronas Dynamic Bass (MDB) function. This is designed to enable the user to hear bass notes that the headphones and/or speakers are not capable of reproducing. Every tone has a fundamental frequency (the ``main tone'') and also several harmonics, which are related to that tone. The human brain has a mechanism whereby it can actually infer the presence of bass notes from the higher harmonics that they would generate.\\
The practical upshot of this is that MDB produces a more authentic sounding bass by tricking the brain in believing it's hearing tones that the headphones or speakers aren't capable of reproducing. Try it and see what you think.\\
The MDB parameters are as follows.
\begin{itemize}
\item \textbf{MDB enable: }
This turns the MDB feature on or off. For many users this will be the only setting they need, since Rockbox picks sensible defaults for the other parameters. MDB is turned off by default.
\item \textbf{MDB strength:}
How loud the harmonics generated by the MDB will be.
\item \textbf{MDB Harmonics:}
The percentage of the low notes that is converted into harmonics. If low notes are causing speaker distortion, this can be set to 100\% to eliminate the fundamental completely and only produce harmonics in the signal. If set to 0\% this is the same as turning the MDB feature off.
\item \textbf{MDB Centre Frequency: }The cutoff frequency of your headphones or speakers. This is usually given in the specification for the headphones/speakers.
\item \textbf{MDB shape: }It is recommended that this parameter be set to 1.5 times the centre frequency.\\
This is the frequency up to which harmonics are generated. Some of the lower fundamentals near the cut{}-off range will have their lower harmonics cut off, since they will be below the range of the speakers. Fundamentals between the cut{}-off frequency and the lower frequency will have their harmonics proportionally boosted to compensate and restore the 'loudness' of these notes.\\
For most users, the defaults should provide an improvement in sound quality and can be safely left as they are. For reference, the defaults Rockbox uses are:
\begin{table}[h!]
\begin{center}
\begin{tabular}{@{}lc@{}}\toprule
Setting & Value \\\midrule
MDB Strength & 50dB \\
MDB Harmonics & 48\% \\
MDB Centre Frequency & 60Hz \\
MDB Shape & 90Hz \\\bottomrule
\end{tabular}
\end{center}
\end{table}
\end{itemize}
}
\opt{SWCODEC}{
\item \textbf{Crossfeed} Crossfeed attempts to make the experience of listening to music on headphones more similar to listening to stereo speakers. When you listen to music through speakers, your right ear hears sound from the left speaker and vice versa. However, the sound from the left speaker reaches your left ear slightly later than the sound from your right ear, and vice versa. Moreover, when listening to speakers, you hear the direct sound from the speakers, but you also hear reflections of that sound as the sound waves bounce off of walls, floors, ceilings, etc. These reflections reach your ears slightly after the direct sound.
The human ear and brain are very good at interpreting the timing differences between direct sounds and reflected sounds and using that information to identify the direction that the sound is coming from. On the other hand, when listening to headphones, your ear hears only the direct sounds, and not reflections. Moreover, your left ear hears only the left channel and the right ear hears only the right channel. The result is that sound from headphones does not provide the same spatial cues to your ear and brain as speakers.
The crossfeed function uses an algorithm to feed a delayed and filtered portion of the signal from the right channel into the left channel and vice versa in order to simulate the spatial cues that the ear and brain receive when listening to non-headphone sources. The result is a better stereo image.
}
\opt{SWCODEC}{
\item \textbf{Equalizer} Rockbox features a parametric equalizer. As the name suggests, a parametric equalizer lets you control several different parameters for each band of the equalizer. Rockbox's parametric EQ is composed of five different EQ bands:
\begin{itemize}
\item \textbf{Band 0: Low shelf filter. }A low shelf filter boosts or lowers all frequencies below the designated cutoff point. The ``bass''control on most home or car stereos is an example of a low shelf filter. The low shelf filter in Rockbox is more flexible than a simple ``bass'' control, because a simple bass control only lets you adjust the amount of gain that is applied. Rockbox lets you control the amount of gain that is applied (i.e., the amount that the bass is boosted or cut) too, but Rockbox also allows you to adjust the ``cutoff'' frequency where the shelving starts to take effect. For example, a cutoff frequency of 50 Hz will adjust only very low frequencies. A cutoff frequency of 200 Hz, on the other hand, will adjust a much wider range of bass frequencies.
\item \textbf{Bands 1-3: Peaking filters.} Peaking EQ filters boost or low a center frequency that you select, as well as the frequencies within a certain distance of that center. Graphic equalizers in home stereos are usually peaking filters. The peaking EQs on Rockbox's parametric equalizer let you adjust three different parameters for each EQ band 1 through 3. The ``center'' parameter controls the center frequency that is adjusted by that EQ band. The ``gain'' parameter controls how much each band is adjusted. Positive numbers make the EQ band louder, while negative numbers make that EQ band quieter. Finally, the ``Q'' parameter controls how wide or narrow each EQ band is. Higher Q values will affect a narrow band of frequencies, while lower EQ values will affect a wider band of frequencies.
\item \textbf{Band 4: High shelf filter.} A high shelf filter boosts or lowers all frequencies above a designated cutoff point. The ``treble'' control on most home or car stereos is an example of a high shelf filter. The high shelf filter is adjusted the same way as the low shelf filter, except that it works on the high end of the frequency spectrum rather than the low end.
\end{itemize}
So, as a general guide, EQ band 0 should be used for lows, EQ bands 1 through 3 should be used for mids, and EQ band 4 should be used for highs.
You can find more information about setting the parametric equalizer and using equalizer presets in the Advanced Topics chapter of this manual.
}
\section{\label{ref:GeneralSettings}General Settings}
\begin{center}
\includegraphics[width=4cm]{configure_rockbox/images/ss-general-settings-\genericimg.png}
\end{center}
\subsection{\label{ref:PlaybackOptions}Playback Options}
This menu is for configuring settings related to audio playback.
\begin{itemize}
\item \textbf{Shuffle}
Select shuffle ON/OFF. This alters how Rockbox will select which next song to play.
\item \textbf{Repeat}
The ``Repeat'' setting is for configuring settings related to repeating of directories or playlists. Repeat modes are Off/One/All/Shuffle:
\begin{itemize}
\item \textbf{Off: }``Off'' means that the current directory or playlist will not repeat when it is finished. (Note: If you have the ``Auto change directory'' option set to ``Yes,'' Rockbox will move on to the next directory on your hard drive. If the ``Auto change directory'' option is set to ``No,'' playback will stop when the current directory or playlist is finished.)
\item\textbf{One: }``One'' means repeat one track over and over.
\item\textbf{All: } ``All'' means that the current directory or playlist will repeat when it is finished. (Note: this option does \textbf{not} shuffle all files on your \dap. Rockbox is playlist oriented. When you play a song, or a directory, or an album, Rockbox creates a playlist and plays it. Thus, to shuffle all songs on the player, you need to create a playlist of all songs on the player, and play that playlist with shuffle mode set to ``All.'')
\item\textbf{Shuffle: }``Shuffle'' means that when the current directory or playlist has finished playing, it will be shuffled and then repeated.
\end{itemize}
\item \textbf{Play Selected First}
This setting controls what happens when you select a file for playback while shuffle mode is on. If the Play Selected First setting is ``Yes,'' the file you selected will be played first. If this setting is ``No,'' a random file in the directory will be played first.
\item \textbf{Resume}
Rockbox can be configured to start playing automatically when you turn on the \dap. If the resume function is set to start automatically playing, Rockbox will start at the point where you last turned off the \dap. The options for the Resume function are:
\begin{enumerate}
\item\textbf{Yes: }``Yes'' means Rockbox will unconditionally try to resume.
\item\textbf{No: }``No'' means Rockbox will not resume. If resume is set to ``No,'' Rockbox will start in the File Browser.
\end{enumerate}
Note: Earlier versions of Rockbox had an "Ask" setting, which would ask whether to resume when the jukebox was turned on. This setting has been eliminated because it was redundant. If resume is set to ``Yes'' simply on the \dap will resume from the point where the \dap was stopped before shutdown.
\item \textbf{FFwd/Rewind}
The options available at this point are:
\begin{enumerate}
\item \textbf{FF/RW Min Step}
The smallest step, in seconds, you want to fast forward or rewind in a track. Options are 1, 2, 3, 4, 5, 6, 8, 10, 15, 20, 25, 30, 45, or 60 seconds.
\item \textbf{FF/RW Accel}
How fast you want search (fastforward or rewind) to accelerate when you hold down the button. ``Off'' means no acceleration. ``2x/1s'' means double the search speed once every second the button is held. ``2x/5s'' means double the search speed once every 5 seconds the button is held.
\end{enumerate}
\item \textbf{Anti-skip Buffer}
This setting allows you to control how much music is stored in the player's memory whilst playing a song, acting as a buffer against shock or playback problems. The player transfers the selected amount of the forthcoming song into its memory at high speed whilst you are playing the song. It keeps a ``rolling'' buffer, which keeps feeding more of the forthcoming song into memory as it goes along. If the \dap is knocked, shaken or jogged heavily while Rockbox is trying to read the hard drive, Rockbox might not be able to read the drive. Rockbox will retry over and over again until it succeeds, but may eventually reach the end of the memory buffer. When that happens, Rockbox must stop playing and wait for more data from the disk, which causes your music to skip. The anti-skip setting tells Rockbox how much extra buffer memory to spare to handle this situation. This setting therefore allows you to reduce the chances of there being a gap or pause during playback of songs.
\opt{MASCODEC}{The anti-skip buffer can be set to a value between 0 and 7 seconds.}
\opt{SWCODEC}{The anti-skip buffer can be set to various values between 5 seconds and 10 minutes.}
\textbf{Tip: }Having a large anti-skip buffer tends to use more power, and may reduce your battery life. It is recommended to always use the lowest possible setting that allows correct and continuous playback.
\item \textbf{Fade On Stop/Pause}
This setting enables and disables a fade effect when you pause or stop playing a song. If the Fade on Stop/Pause option is set to ``Yes,'' your music will fade out when you press STOP or PAUSE, and fade in when you resume playback.
\item \textbf{Party Mode}
The ``Party Mode'' enables unstoppable music playback. When new songs are selected, they are added to the end of the current dynamic playlist instead of being played immediately. The PLAY and STOP buttons are disabled.
\opt{SWCODEC}{
\item \textbf{Crossfade}
This setting enables a cross-fader. At the end of a song, the song will fade out as the next song fades in, creating a smooth transition between songs. Options:
\begin{itemize}
\item \textbf{Enable crossfade} If set to ``Off,'' crossfade is disabled. If set to ``Always,'' songs will always cross-fade into one another. If set to ``Shuffle,'' crossfade is enabled when the shuffle feature is set to ``Yes,'' but disabled otherwise.
\item \textbf{Fade in delay} TODO find the place in the IRC logs where Slasheri explained this.
\item \textbf{Fade in duration} The length of time, in seconds, that it takes your music to fade in.
\item \textbf{Fade out delay} TODO find the place in the IRC logs where Slasheri explained this.
\item \textbf{Fade out duration} The length of time, in seconds, that it takes your music to fade out.
\item \textbf{Fade out mode} If set to ``Crossfade," one song will fade out and the next song will simultaneously fade in. If set to ``Mix,'' the currently playing song will fade out according to the fade out settings, but the next song will simply start, without fading in.
\end{itemize}
\textbf{TIP} The crossfade setting is particularly effective when the player is set on shuffle.
}
\opt{SWCODEC}{
\item \textbf{replaygain}
This allows you to control the replaygain function. The purpose of replaygain is to adjust the volume of the music played so that all songs (or albums, depending on your settings) have the same apparent volume. This prevents sudden changes in volume when changing between songs recorded at different volume levels.
For replaygain to work, the songs must have been processed by a program that adds replaygain information as ID3 tags (or vorbis tags for certain formats). Note that APEv2 tags are not currently supported.
Options for replaygain are:
\begin{itemize}
\item \textbf{Enable replaygain} This turns on/off the replaygain function.
\item \textbf{Prevent clipping} Avoid clipping of a song's waveform. If a song would clip during playback, the volume is lowered for that song. Replaygain information is needed for this to work.
\item \textbf{Replaygain type} Choose the type of replaygain to apply:
\begin{itemize}
\item \textbf{Album gain} Maintain a constant volume level between albums, but keep any intentional volume variations between songs in an album. (If album gain value is not available, uses track gain information).
\item \textbf{Track gain} Maintain a constant volume level between tracks. If track gain value is not available, no replaygain is applied.
\item \textbf{Track gain if shuffling} Maintains a constant volume between tracks if shuffle mode is selected. Reverts to album mode if shuffle is off.
\end{itemize}
\item \textbf{Pre-amp} This allows you to adjust the volume when replaygain is applied. Replaygain often lowers the volume, sometimes quite much, so here you can compensate for that. Please note that a (large) positive pre-amp setting can cause clipping, unless prevent clipping is enabled. The pre-amp can be set to any decibel (dB) value between -12dB and +12dB, in increments of 0.1 dB.
\end{itemize}
}
\item \textbf{ID3 tag priority}
ID3 tags in an MP3 file contain information about the artist, title, album etc. of the track. This option controls whether Rockbox uses the information from ID3v2 tags in preference to that from ID3v1 tags when both types of tag are present.
\end{itemize}
\subsection{File View}
This menu deals with options relating to how the file browser displays files
\begin{itemize}
\item \textbf{Sort Case Sensitive}
If this option is enabled files that start with a lower case letter will appear after the files that start with an upper case letter have all been listed If disabled, then case will be ignored when sorting files.
\item \textbf{Sort Directories}
This option controls how Rockbox sorts folders. The default is to sort them alphabetically. ``By date'' sorts them with the oldest folder first. ``By newest date'' sorts them with the newest folder first.
\item \textbf{Sort Files}
This option controls how Rockbox sorts files. In addition to the options for directory sorting above, there is a ``By type'' option which sorts files alphabetically by their type (such as .mp3) then alphabetically within each type.
\item \textbf{\label{ref:ShowFiles}Show Files}
Controls which files are displayed in the directory browser:
\begin{itemize}
\item \textbf{Music: }
Only directories, .m3u files and the supported \emph{audio} fileformats are shown. Extensions are strippe'd. Files anddirectories starting with . Or with the ``hidden'' flag set are hidden.
\item \textbf{Playlists:}
Only shows directories and playlists, for simplified navigation.
\item \textbf{Supported:}
All directories and files Rockbox understands (see page \pageref{ref:Supportedfileformats}) are shown. Files and directories starting with . or with the ``hidden'' flag set are hidden.
\item \textbf{All:}
All files and directories are shown. Extensions are shown. No files or directories arehidden
\end{itemize}
\item \textbf{Follow Playlist}
If Follow Playlist is set to ``Yes'', you will find yourself in the same directory as the currently playing file if you go to the Directory Browser from the WPS. If set to ``No'', you will stay in the same directory as you were last in.
\item \textbf{Show Icons}
This indicates whether Rockbox will display an icon representing what type a file is on the left of the file in the browser. For details of these icons, please see page \pageref{ref:Supportedfileformats}.
\end{itemize}
\subsection{\label{ref:Displayoptions}Display Options}
\begin{itemize}
\item \textbf{Browse fonts}
Browse the fonts that reside in your \fname{/.rockbox} directory. Selecting one will activate it. See page \pageref{ref:Loadingfonts} for further details about fonts.
\item \textbf{Browse WPS files}
Opens the file browser in the \textbf{/.rockbox} directory and displays all .wps files. Selecting one will activate it, stop will exit back to the menu.\\
For further information about the WPS see page \pageref{ref:WPS}. For information about editing a .wps file see page \pageref{ref:ConfiguringtheWPS}.
\item \textbf{LCD Settings}
This submenu contains settings that relate to the display of the \dap.
\begin{itemize}
\item \textbf{Backlight:}
How long the backlight shines after a key press. Set to OFF to never light it, set to ON to never shut it off or set a preferred timeout period.
\item \textbf{Backlight on WhenPlugged:}
This option turns the backlight on constantly while the charger cable is connected.
\item \textbf{Caption Backlight:} This option turns the backlight on for 25 seconds either side of the start of a new track so that the display can be read to see song information.
\item \textbf{Contrast:} Changes the contrast of your LCD display. Warning: Setting the contrast too dark or too light can make it hard to find this menu option again!
\opt{recorder,recorderv2fm,ondio,h1xx,h300,ipodnano,ipodcolor,ipodvideo}{
\item \textbf{LCD Mode}: This setting lets you invert the whole screen, so now you get a black background and green text graphics.
}
\item \textbf{Upside Down: }Displays the screen so that the top of the display is nearest the buttons. This is sometimes useful when carrying the \dap in a pocket for easy access to the headphone socket.
\item \textbf{Line Selector: }Select this option to have a bar of inverted text (``Bar'' option) mark the current line in the File Browser rather than the default arrow to the left (``Pointer'' option). This gives slightly more room for filenames.
\end{itemize}
\item \textbf{Scrolling}
This feature controls how text will scroll in Rockbox. You can configure the following parameters:
\begin{itemize}
\item \textbf{Scroll Speed:}
Controls how many times per second the scrolling text moves a step.
\item \textbf{Scroll StartDelay:}
Controls how many milliseconds Rockbox should wait before a new text begins scrolling.
\opt{recorder,recorderv2fm,ondio,h1xx,h300,ipodnano,ipodcolor,ipodvideo}{
\item \textbf{Scroll Step Size:}
Controls how many pixels the text scroll should move for each step.
}
\item \textbf{Bidirectional Scroll Limit: }
Rockbox has two different scroll methods, always scrolling the text to the left, and when the line has ended, beginning again at the start, or moving to the left until you can read the end of the line, and scroll right until you see the beginning again. Rockbox chooses which method it should use, depending of how much it has to scroll left. This setting lets you tell Rockbox where that limit is, expressed in percentage of line length.
\end{itemize}
\opt{recorder,recorderv2fm,ondio,h1xx,h300,ipodnano,ipodcolor,ipodvideo}{
\item \textbf{Status/Scrollbar}
Settings related to on screen status display and the scrollbar.
\begin{itemize}
\item \textbf{Scroll Bar: }Enables or disables the scroll bar at the left.
\item \textbf{Status Bar: }Enables or disables the status bar at the upper side.
\item \textbf{Button Bar:} Enables or disables the button bar prompts for the F keys at the bottom of the screen.
\item \textbf{Volume Display:} Controls whether the volume is displayed as a graphic or a numerical percentage value on the Status Bar.
\item \textbf{Battery Display: }Controls whether the battery charge status is displayed as a graphic or numerical percentage value on the Status Bar.
\end{itemize}
}
\opt{recorder,recorderv2fm,ondio,h1xx,h300,ipodnano,ipodcolor,ipodvideo}{
\item \textbf{Peak Meter}
The peak meter can be configured with a number of parameters. (For a description of the peak meter see page \pageref{ref:Peakmeter}.)
\begin{itemize}
\item \textbf{Peak Release:}
This determines how fast the bar shrinks when the music becomes softer. Lower values make the peak meter look smoother.
\item \textbf{Peak Hold Time:}
Specifies the time after which the peak indicator will reset. If you set this value e.g. to 5s then the peak indicator displays the loudest volume value that occurred within the last 5 seconds. Big values are good if you want to find the peak level of a song, which might be of interest when copying music from the \dap via the analogue output to some other recording device.
\item \textbf{Clip Hold Time:}
How long the clipping indicator will be visible after clipping was detected
\item \textbf{Performance:}
In high performance mode, the peak meter is updated as often as possible. This reduces the chance of missing a peak value, making the peak meter more precise. In energy save mode the peak meter is updated just often enough to look fluid. This reduces the load on the CPU and thus saves a little bit of energy. If you crave every second of runtime for your \dap or simply use the peak meter as a screen effect, the use of energy save mode is recommended. If you want to use the peak meter as a measuring instrument you'll want to use high performance mode.
\item \textbf{Scale:}
Select whether the peak meter displays linear or logarithmic values. In ``dB'' (decibel) scale the volume values are scaled logarithmically. This very similar to the perception of loudness. The volume meters of digital audio devices usually are scaled this way. If you are interested in the power level that is applied to your headphones you should choose ``linear'' display. Unfortunately this value doesn't have real units like volts or watts since that depends on the phones. So they can only be displayed as percentage values.
\item \textbf{Minimum and maximum range:}
These two options define the full value range that the peak meter displays. Recommended values for dB's are {}-40 for min. and 0 for maximum. For linear display, use 0 and 100\%. Note that {}-40 dB's is approximately 1\% in linear value, but if you change the minimum setting in linear mode slightly and then change to dbFs there will be a large change. You can use these values for 'zooming' into the peak meter.
\end{itemize}
}
\end{itemize}
\subsection{\label{ref:SystemOptions}System Options}
\begin{itemize}
\item \textbf{Battery}
Options relating to the batteries in the \dap.
\begin{itemize}
\item \textbf{Battery Capacity} can be used to tell Rockbox what capacity (in mAh) of battery is being used inside it.
\opt{player,recorder,recorderv2fm,ondio}{The default is 1500mAh for NiMH battery based units, and 2300mAh for LiOn battery based units, which is the capacity value for the standard batteries shipped with these units.}
\opt{h1xx,h300}{The default is 1300mAh.}
This value is used for calculating remaining battery life.
\opt{recorder}{
\item \textbf{Deep discharge}
Set this to ON if you intend to keep your charger connected for a long period of time. It lets the batteries go down to 10\% before starting to charge again. Setting this to OFF will cause the charging to restart on 95\%.
}
\opt{recorder}{
\item \textbf{Trickle Charge}
The \dap cannot be turned off while the charger is connected.
Therefore, trickle charge is needed to keep the batteries full after
charging has completed. For more in depth information about charging
see Battery FAQ in your \textbf{/.rockbox/docs }directory.
}
\end{itemize}
\item \textbf{Disk}
Options relating to the hard disk.
\begin{itemize}
\item \textbf{DiskSpindown:}
Rockbox has a timer that makes it spin down the hard disk after being idle for acertain time. You can modify this timeout here. This idle time is only affected by user activity, like navigating through file browser. When the hard disk spins up to fill mp3 buffer, it automatically spins down afterwards.
\opt{recorder,h1xx,h300}{
\item \textbf{Disk Poweroff:}
Whether the disk is powered OFF or only set to ``sleep'' when spun down. Power off uses less power but takes longer to spin{}-up.}
\end{itemize}
\opt{recorder,recorderv2fm,h3xx}{
\item \textbf{Time and Date}
Time related menu options.
\begin{itemize}
\item \textbf{Set Time/Date: }
Set current time and date.
\item \textbf{Time Format: }
Choose 12 or 24 Hour clock.
\end{itemize}
}
\item \textbf{\label{ref:idlepoweroff}Idle Poweroff}
Rockbox can be configured to turn off power after the unit has been idle for a defined number of minutes. The unit is idle when playback is stopped or paused. It is not idle while the USB or charger is connected, or while recording.
\item \textbf{Sleep Timer}
This option lets you power off your \dap after playing for a given time. \opt{recorderv2fm}{This setting is reset on boot. Using this option disables the \textbf{Wake up alarm} (see below).}
\opt{recorderv2fm}{
\item \textbf{Wake up alarm (Recorder v2/FM only)}
This option turns the \dap off and then starts it up again at the specified time. This is most useful when combined with the Resume setting in the Playback options set to ``Yes'', so that the \dap wakes up and immediately starts playing music. Use LEFT and RIGHT to adjust the minutes setting, UP and DOWN to adjust the HOURS. PLAY confirms the alarm and shuts your \dap down, and STOP cancels setting an alarm. If the \dap is turned on again before the alarm occurs the alarm will be canceled. Using this option disables the \textbf{Sleep Timer} (see above).
}
\item \textbf{Limits}
This submenu relates to limits in the Rockbox operating system.
\begin{itemize}
\item \textbf{Max files in dir browser:}
Configurable limit of files in the directory browser (file buffer size). You can configure the size to be between 50 and 10000 files in steps of 50 files. The default is 400, higher values will shorten the music buffer.\\
\item \textbf{Max playlist size:}
Option to configure the maximum size of a playlist. The playlist size can be between 1000 and 20000 files in
steps of 1000. By default it is 10000. Higher values will shorten the music buffer.\\
\end{itemize}
\opt{player,recorder,recorderv2fm}{
\item \textbf{Car Adapter Mode}
This option turns on and off the car ignition auto stop function.
When using the \dap in a car, car adapter mode automatically stops playback on the \dap when power (i.e. from cigarette lighter power adapter) to the external DC in jack is turned off.
When the external power off condition is detected, the Car Adapter Mode function only pauses the playback. In order to shut down the \dap completely the \textbf{Idle Poweroff} function (see above) must also be set.
If power to the DC in jack is turned back on before the \textbf{Idle Poweroff} function has shut the \dap off, playback will be resumed 5 seconds after the power is applied. This delay is to allow for the time while the car engine is being started. Once the \dap is shut off either manually, or automatically with the \textbf{Idle Poweroff}function, it must be powered up manually to resume playback.
}
\opt{player}{
\item \textbf{Line In (Player only)}
This option activates the line in port on \dap Player, which is off by default.
This is useful for such applications as:
\begin{itemize}
\item Game boy {}-{\textgreater} \dap {}-{\textgreater} human
\item laptop {}-{\textgreater} \dap {}-{\textgreater}human
\item LAN party computer {}-{\textgreater} \dap {}-{\textgreater} human
\end{itemize}
}
\item \textbf{Manage settings}
This submenu deals with loading and saving settings.
\begin{itemize}
\item \textbf{Browse .cfg Files: }
This displays a list of configuration (.cfg) files stored in the \textbf{/.rockbox} system directory. This is useful if the \dap is plugged into more than one different output device (e.g. headphones, computer, car stereo, hi{}-fi) so that a settings file can be maintained for each.
\item \textbf{Browse Firmwares:}
This displays a list of firmware file in the \fname{/.rockbox} system directory. Playing a firmware file loads it into memory. Thus it is possible to run the original Archos firmware or a different version of Rockbox from here assuming that you have the right files installed on your disk.
\item \textbf{Reset Settings: }
This wipes the saved settings in the \dap and resets all settings to their default values.
\item \textbf{Write .cfg file: }
Saves the current settings into a .cfg file for later use with \textbf{Browse .cfg Files} above.
\end{itemize}
\end{itemize}
\subsection{\label{ref:Bookmarkconfigactual}Bookmarking}
\begin{itemize}
\item \textbf{Bookmark on Stop}
Write a bookmark to the disk whenever the stop key is pressed. If playback is stopped it can be resumed easily at a later time. The \textbf{Resume} function remembers your position in the most recently accessed track regardless of this setting.
\item \textbf{Load Last Bookmark}
When this is on, Rockbox automatically returns to the position of the last bookmark within a file when it is played. If set to Ask, Rockbox will ask the user whether they want to start from the beginning or the bookmark. When set to no, playback always starts from the beginning and the Bookmark file must be played or \textbf{Load Bookmark} selected from the \textbf{Bookmarks} submenu of the Main Menu while the file is playing.
\item \textbf{Maintain a list of Recently Used Bookmarks}
If this option is turned on, Rockbox will store a list of Bookmarks that have been accessed recently. This is then accessible from the \textbf{Recent Bookmarks} option of the \textbf{Bookmarks} submenu of the Main Menu.
\end{itemize}
\subsection{\label{ref:Language}Language}
This setting controls the language of the Rockbox user interface. Selecting a language will activate it. The language files must be in the \textbf{/.rockbox/lang/} directory. See page \pageref{ref:Loadinglanguages} for further details about languages.
\subsection{\label{ref:Voiceconfiguration}Voice}
\begin{itemize}
\item \textbf{Voice Menus}
This option turns on the Voice User Interface, which will read out menu items and settings as they are selected by the cursor. In order for this to work, a voice file must be present in the \textbf{/.rockbox/lang/} directory on the \dap. Voice files are large (1.5MB) and are not shipped with Rockbox by default.
The voice file is the name of the language for which it is made, followed by the extension .voice. So for English, the file name would be \fname{english.voice}.
This option is on by default. It will do nothing unless the appropriate .voice file is installed in the correct place on the \dap.
\begin{itemize}
\item \textbf{Limitations}
\begin{itemize}
\item Setting the Sound Option \textbf{Channels} to ``karaoke'' may disable voice menus.
\item Plugins and the wake up alarm do not support voice features.
\end{itemize}
\end{itemize}
\item \textbf{Voice Directories}
This option turns on the speaking of directory names. The \dap is not powerful enough to produce these voices in real time, so a number of options are available.
\begin{itemize}
\item \textbf{.talk mp3 clip: }
Use special pre{}-recorded MP3 files (\fname{\_dirname.talk}) in each directory. These must be generated in advance, and are typically produced synthetically using a text to speech engine on a PC. If no such file exists, the output is as for the ``numbers'' option below.
\item \textbf{Spell: }
Speak the directory name by spelling it out letter by letter. Support is provided only for the most common letters and punctuation.
\item \textbf{Numbers: }
Each directory is assigned a number based upon its position in the file list. They are then announced as ``Directory 1'', ``Directory 2'' etc.
\item \textbf{Off: }
No attempt will be made to speak directory names.
\end{itemize}
\item \textbf{Voice Filenames}
This option turns on the speaking of directory names. The options provided are ``Spell'', ``Numbers'', and ``Off'' which function the same as for \textbf{Voice Directories} and ``.talk mp3 clip'', which functions as above except that the files are named with the same name as the music file (e.g. \fname{Punkadiddle.mp3 } would require a file called \textbf{Punkadiddle.mp3.talk}).
\end{itemize}
\end{itemize}
See \url{http://www.rockbox.org/twiki/bin/view/Main/VoiceHowto} for more details on configuring speech support in Rockbox.