e48cc2a491
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@4602 a1c6a512-1295-4272-9138-f99709370657
307 lines
9.2 KiB
ArmAsm
Executable file
307 lines
9.2 KiB
ArmAsm
Executable file
/***************************************************************************
|
|
* __________ __ ___.
|
|
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
|
|
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
|
|
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
|
|
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
|
|
* \/ \/ \/ \/ \/
|
|
* $Id$
|
|
*
|
|
* Copyright (C) 2004 by Jens Arnold
|
|
* Based on the work of Alan Korr and Jörg Hohensohn
|
|
*
|
|
* All files in this archive are subject to the GNU General Public License.
|
|
* See the file COPYING in the source tree root for full license agreement.
|
|
*
|
|
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
|
|
* KIND, either express or implied.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#include "config.h"
|
|
#include "sh7034.h"
|
|
|
|
#define LCDR (PBDR_ADDR+1)
|
|
|
|
#ifdef HAVE_LCD_CHARCELLS
|
|
#define LCD_DS 1 /* PB0 = 1 --- 0001 --- LCD-DS */
|
|
#define LCD_CS 2 /* PB1 = 1 --- 0010 --- /LCD-CS */
|
|
#define LCD_SD 4 /* PB2 = 1 --- 0100 --- LCD-SD */
|
|
#define LCD_SC 8 /* PB3 = 1 --- 1000 --- LCD-SC */
|
|
#else
|
|
#define LCD_SD 1 /* PB0 = 1 --- 0001 */
|
|
#define LCD_SC 2 /* PB1 = 1 --- 0010 */
|
|
#define LCD_RS 4 /* PB2 = 1 --- 0100 */
|
|
#define LCD_CS 8 /* PB3 = 1 --- 1000 */
|
|
#define LCD_DS LCD_RS
|
|
#endif
|
|
|
|
/*
|
|
* About /CS,DS,SC,SD
|
|
* ------------------
|
|
*
|
|
* LCD on JBP and JBR uses a SPI protocol to receive orders (SDA and SCK lines)
|
|
*
|
|
* - /CS -> Chip Selection line :
|
|
* 0 : LCD chipset is activated.
|
|
* - DS -> Data Selection line, latched at the rising edge
|
|
* of the 8th serial clock (*) :
|
|
* 0 : instruction register,
|
|
* 1 : data register;
|
|
* - SC -> Serial Clock line (SDA).
|
|
* - SD -> Serial Data line (SCK), latched at the rising edge
|
|
* of each serial clock (*).
|
|
*
|
|
* _ _
|
|
* /CS \ /
|
|
* \______________________________________________________/
|
|
* _____ ____ ____ ____ ____ ____ ____ ____ ____ _____
|
|
* SD \/ D7 \/ D6 \/ D5 \/ D4 \/ D3 \/ D2 \/ D1 \/ D0 \/
|
|
* _____/\____/\____/\____/\____/\____/\____/\____/\____/\_____
|
|
*
|
|
* _____ _ _ _ _ _ _ _ ________
|
|
* SC \ * \ * \ * \ * \ * \ * \ * \ *
|
|
* \_/ \_/ \_/ \_/ \_/ \_/ \_/ \_/
|
|
* _ _________________________________________________________
|
|
* DS \/
|
|
* _/\_________________________________________________________
|
|
*
|
|
*/
|
|
|
|
.section .icode,"ax",@progbits
|
|
|
|
.align 2
|
|
.global _lcd_write_command
|
|
.type _lcd_write_command,@function
|
|
|
|
/* Write a command byte to the lcd controller
|
|
*
|
|
* Arguments:
|
|
* r4 - data byte (int)
|
|
*
|
|
* Register usage:
|
|
* r0 - scratch
|
|
* r1 - data byte (copied)
|
|
* r2 - precalculated port value (CS, DS and SC low, SD high),
|
|
* negated (neg)!
|
|
* r3 - lcd port address
|
|
* r5 - 1 (byte count for reuse of the loop in _lcd_write_data)
|
|
*/
|
|
|
|
_lcd_write_command:
|
|
mov.l .lcdr,r3 /* put lcd data port address in r3 */
|
|
mov r4,r1 /* copy data byte to r1 */
|
|
mov #1,r5 /* set byte count to 1 (!) */
|
|
|
|
/* This code will fail if an interrupt changes the contents of PBDRL.
|
|
* If so, we must disable the interrupt here. */
|
|
|
|
mov.b @r3,r0 /* r0 = PBDRL */
|
|
or #(LCD_SD),r0 /* r0 |= LCD_SD */
|
|
and #(~(LCD_CS|LCD_DS|LCD_SC)),r0 /* r0 &= ~(LCD_CS|LCD_DS|LCD_SC) */
|
|
|
|
bra .single_transfer /* jump into the transfer loop */
|
|
neg r0,r2 /* r2 = 0 - r0 */
|
|
|
|
|
|
.align 2
|
|
.global _lcd_write_data
|
|
.type _lcd_write_data,@function
|
|
|
|
|
|
/* A high performance function to write data to the display,
|
|
* one or multiple bytes.
|
|
*
|
|
* Arguments:
|
|
* r4 - data address
|
|
* r5 - byte count
|
|
*
|
|
* Register usage:
|
|
* r0 - scratch
|
|
* r1 - current data byte
|
|
* r2 - precalculated port value (CS and SC low, DS and SD high),
|
|
* negated (neg)!
|
|
* r3 - lcd port address
|
|
*/
|
|
|
|
_lcd_write_data:
|
|
mov.l .lcdr,r3 /* put lcd data port address in r3 */
|
|
nop /* align here */
|
|
|
|
/* This code will fail if an interrupt changes the contents of PBDRL.
|
|
* If so, we must disable the interrupt here. If disabling interrupts
|
|
* for a long time (~9200 clks = ~830 µs for transferring 112 bytes on
|
|
* recorders)is undesirable, the loop has to be rewritten to
|
|
* disable/precalculate/transfer/enable for each iteration. However,
|
|
* this would significantly decrease performance. */
|
|
|
|
mov.b @r3,r0 /* r0 = PBDRL */
|
|
or #(LCD_DS|LCD_SD),r0 /* r0 |= LCD_DS|LCD_SD */
|
|
and #(~(LCD_CS|LCD_SC)),r0 /* r0 &= ~(LCD_CS|LCD_SC) */
|
|
neg r0,r2 /* r2 = 0 - r0 */
|
|
|
|
#ifdef HAVE_LCD_CHARCELLS
|
|
/* optimized player version, also works for recorders */
|
|
|
|
.align 2
|
|
.multi_transfer:
|
|
mov.b @r4+,r1 /* load data byte from memory */
|
|
|
|
.single_transfer:
|
|
shll16 r1 /* shift data to most significant byte */
|
|
shll8 r1
|
|
|
|
shll r1 /* shift the msb into carry */
|
|
neg r2,r0 /* copy negated precalculated port value */
|
|
/* uses neg here for compatibility with recorder version */
|
|
bt 1f /* data bit = 1? */
|
|
and #(~LCD_SD),r0 /* no: r0 &= ~LCD_SD */
|
|
1:
|
|
shll r1 /* next shift here for alignment */
|
|
mov.b r0,@r3 /* set data to port */
|
|
or #(LCD_SC),r0 /* rise SC (independent of SD level) */
|
|
mov.b r0,@r3 /* set to port */
|
|
|
|
neg r2,r0
|
|
bt 1f
|
|
and #(~LCD_SD),r0
|
|
1:
|
|
mov.b r0,@r3
|
|
or #(LCD_SC),r0
|
|
mov.b r0,@r3
|
|
|
|
shll r1
|
|
neg r2,r0
|
|
bt 1f
|
|
and #(~LCD_SD),r0
|
|
1:
|
|
shll r1
|
|
mov.b r0,@r3
|
|
or #(LCD_SC),r0
|
|
mov.b r0,@r3
|
|
|
|
neg r2,r0
|
|
bt 1f
|
|
and #(~LCD_SD),r0
|
|
1:
|
|
mov.b r0,@r3
|
|
or #(LCD_SC),r0
|
|
mov.b r0,@r3
|
|
|
|
shll r1
|
|
neg r2,r0
|
|
bt 1f
|
|
and #(~LCD_SD),r0
|
|
1:
|
|
shll r1
|
|
mov.b r0,@r3
|
|
or #(LCD_SC),r0
|
|
mov.b r0,@r3
|
|
|
|
neg r2,r0
|
|
bt 1f
|
|
and #(~LCD_SD),r0
|
|
1:
|
|
mov.b r0,@r3
|
|
or #(LCD_SC),r0
|
|
mov.b r0,@r3
|
|
|
|
shll r1
|
|
neg r2,r0
|
|
bt 1f
|
|
and #(~LCD_SD),r0
|
|
1:
|
|
shll r1
|
|
mov.b r0,@r3
|
|
or #(LCD_SC),r0
|
|
mov.b r0,@r3
|
|
|
|
neg r2,r0
|
|
bt 1f
|
|
and #(~LCD_SD),r0
|
|
1:
|
|
mov.b r0,@r3
|
|
or #(LCD_SC),r0
|
|
mov.b r0,@r3
|
|
|
|
#else /* HAVE_LCD_CHARCELLS */
|
|
/* further optimized version, exploits that SD is on bit 0 for recorders */
|
|
|
|
.align 2
|
|
.multi_transfer:
|
|
mov.b @r4+,r1 /* load data byte from memory */
|
|
nop
|
|
|
|
.single_transfer:
|
|
shll16 r1 /* shift data to most significant byte */
|
|
shll8 r1
|
|
not r1,r1 /* and invert for use with negc */
|
|
|
|
shll r1 /* shift the MSB into carry */
|
|
negc r2,r0 /* carry to SD, SC low */
|
|
shll r1 /* next shift here for alignment */
|
|
mov.b r0,@r3 /* set data to port */
|
|
or #(LCD_SC),r0 /* rise SC (independent of SD level) */
|
|
mov.b r0,@r3 /* set to port */
|
|
|
|
negc r2,r0
|
|
mov.b r0,@r3
|
|
or #(LCD_SC),r0
|
|
mov.b r0,@r3
|
|
|
|
shll r1
|
|
negc r2,r0
|
|
shll r1
|
|
mov.b r0,@r3
|
|
or #(LCD_SC),r0
|
|
mov.b r0,@r3
|
|
|
|
negc r2,r0
|
|
mov.b r0,@r3
|
|
or #(LCD_SC),r0
|
|
mov.b r0,@r3
|
|
|
|
shll r1
|
|
negc r2,r0
|
|
shll r1
|
|
mov.b r0,@r3
|
|
or #(LCD_SC),r0
|
|
mov.b r0,@r3
|
|
|
|
negc r2,r0
|
|
mov.b r0,@r3
|
|
or #(LCD_SC),r0
|
|
mov.b r0,@r3
|
|
|
|
shll r1
|
|
negc r2,r0
|
|
shll r1
|
|
mov.b r0,@r3
|
|
or #(LCD_SC),r0
|
|
mov.b r0,@r3
|
|
|
|
negc r2,r0
|
|
mov.b r0,@r3
|
|
or #(LCD_SC),r0
|
|
mov.b r0,@r3
|
|
|
|
#endif /* HAVE_LCD_CHARCELLS */
|
|
|
|
add #-1,r5 /* decrease byte count */
|
|
tst r5,r5 /* r5 == 0 ? */
|
|
bf .multi_transfer /* no: next iteration */
|
|
|
|
or #(LCD_CS|LCD_DS|LCD_SD|LCD_SC),r0 /* restore port */
|
|
rts
|
|
mov.b r0,@r3
|
|
|
|
/* This is the place to reenable the interrupts, if we have disabled
|
|
* them. See above. */
|
|
|
|
.align 2
|
|
.lcdr:
|
|
.long LCDR
|
|
|
|
.end:
|
|
.size _lcd_write_command,.end-_lcd_write_command
|
|
|