eac1ca22bd
NOTE: this commit does not introduce any change, ideally even the binary should
be almost the same. I checked the disassembly by hand and there are only a few
differences here and there, mostly the compiler decides to compile very close
expressions slightly differently. I tried to run the new code on several targets
to make sure and saw no difference.
The major syntax changes of the new headers are as follows:
- BF_{WR,SET,CLR} are now superpowerful and allows to set several fileds at once:
BF_WR(reg, field1(value1), field2(value2), ...)
- BF_CS (use like BF_WR) does a write to reg_CLR and then reg_SET instead of RMW
- there is no more need for macros like BF_{WR_,SET,CLR}_V, since one can simply
BF_WR with field_V(name)
- the old BF_SETV macro has no trivial equivalent and is replaced with its
its equivalent for BF_WR(reg_SET, ...)
I also rename the register headers: "regs/regs-x.h" -> "regs/x.h" to avoid the
redundant "regs".
Final note: the registers were generated using the following command:
./headergen_v2 -g imx -o ../../firmware/target/arm/imx233/regs/ desc/regs-stmp3{600,700,780}.xml
Change-Id: I7485e8b4315a0929a8edb63e7fa1edcaa54b1edc
64 lines
2.1 KiB
C
64 lines
2.1 KiB
C
/***************************************************************************
|
|
* __________ __ ___.
|
|
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
|
|
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
|
|
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
|
|
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
|
|
* \/ \/ \/ \/ \/
|
|
* $Id$
|
|
*
|
|
* Copyright (C) 2011 by Amaury Pouly
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* as published by the Free Software Foundation; either version 2
|
|
* of the License, or (at your option) any later version.
|
|
*
|
|
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
|
|
* KIND, either express or implied.
|
|
*
|
|
****************************************************************************/
|
|
#ifndef __audioin_imx233__
|
|
#define __audioin_imx233__
|
|
|
|
#include "config.h"
|
|
#include "cpu.h"
|
|
#include "system.h"
|
|
|
|
#define AUDIOIN_SELECT_MICROPHONE 0
|
|
#define AUDIOIN_SELECT_LINE1 1
|
|
#define AUDIOIN_SELECT_HEADPHONE 2
|
|
#define AUDIOIN_SELECT_LINE2 3
|
|
|
|
struct imx233_audioin_info_t
|
|
{
|
|
// NOTE there is a convention here: adc -> adcvol -> adcmute
|
|
int freq; // in mHz
|
|
int muxselect[2];
|
|
bool adc;
|
|
int adcvol[2]; // in tenth-dB, l/r
|
|
bool adcmute[2]; // l/r
|
|
bool mux;
|
|
int muxvol[2]; // in tenth-db, l/r
|
|
bool muxmute[2]; // l/r
|
|
bool mic;
|
|
int micvol[2]; // in tenth-db, l/r
|
|
int micmute[2]; // l/r
|
|
};
|
|
|
|
void imx233_audioin_preinit(void);
|
|
void imx233_audioin_postinit(void);
|
|
void imx233_audioin_open(void);
|
|
void imx233_audioin_close(void);
|
|
/* use AUDIONIN_SELECT_* values */
|
|
void imx233_audioin_select_mux_input(bool right, int select);
|
|
/* volume in half dB */
|
|
void imx233_audioin_set_vol(bool right, int vol, int select);
|
|
/* frequency index, NOT the frequency itself */
|
|
void imx233_audioin_set_freq(int fsel);
|
|
/* enable microphone */
|
|
void imx233_audioin_enable_mic(bool enable);
|
|
|
|
struct imx233_audioin_info_t imx233_audioin_get_info(void);
|
|
|
|
#endif /* __audioin_imx233__ */
|