Robert Kukla ea92e4c2d7 m:robe 100: add USB detection ... git-svn-id: svn://svn.rockbox.org/rockbox/trunk@16480 a1c6a512-1295-4272-9138-f99709370657		2008-03-02 13:07:11 +00:00
..
archos/av300
imx31	Bring the IMX31 serial driver in line with the CONTRIBUTING guidelines.	2008-02-19 14:15:59 +00:00
ipod	Revert LCD changes - make sure the backlight remains on as a visible sign that the unit has powered off	2008-02-14 20:48:17 +00:00
iriver	H10-20GB: Commit the first patch in FS#8533 to fix the mpegplayer display problem where only half the data was reaching the display on some players. Two individuals report that it corrects it.	2008-02-01 02:02:38 +00:00
olympus/mrobe-100	m:robe 100 - now that we have working buttons, we can enable backlight on/off.	2008-02-24 04:30:05 +00:00
pnx0101
s3c2440	Fix the red.	2008-02-13 05:49:48 +00:00
sandisk	acknowledge USB disconnect. This wasn't always done anymore since the usb_wait_for_disconnect() is gone.	2008-02-28 22:51:39 +00:00
tatung/tpj1022
tcc77x
tcc780x	a very basic power_off function	2008-02-16 13:01:30 +00:00
tms320dm320	Finally, out goes struct spinlock for anything but mutiprocessor targets where it becomes a reenterable corelock.	2008-01-18 13:12:33 +00:00
adc-pp5020.c	make mrobe100 work again	2008-02-10 16:06:01 +00:00
ata-as-arm.S
ata-pp5002.c
ata-pp5020.c
ata-target.h
audio-pp.c
crt0-pp-bl.S	Enable dualcore for the pp5002 processor by adding the needed cache handling and sleep/wakeup sync to the kernel. Refine some handling of fw/bl startup for all.	2007-11-27 01:20:26 +00:00
crt0-pp.S	Enable dualcore for the pp5002 processor by adding the needed cache handling and sleep/wakeup sync to the kernel. Refine some handling of fw/bl startup for all.	2007-11-27 01:20:26 +00:00
i2c-pp.c
i2c-telechips.c	Initial Cowon D2 commit:	2008-01-14 22:04:48 +00:00
i2s-pp.c
lcd-as-memframe.S
memcpy-arm.S
memmove-arm.S
memset-arm.S
memset16-arm.S
mmu-arm.c
mmu-arm.h
pcm-pp.c	audio on the m:robe 100	2008-01-20 12:59:23 +00:00
system-arm.h
system-pp502x.c	Driver for the Synaptics touchpad on the m:robe 100 based on the 3-wire interface spec. Needs some tweaking as it's too sensitive with the default hardware settings. For now, the vertical strip is divided into up/select/down buttons. Also, redo the keymap (using the Gigabeat as a starting point), but it still needs a good bit of work.	2008-02-24 04:12:16 +00:00
system-pp5002.c	Enable dualcore for the pp5002 processor by adding the needed cache handling and sleep/wakeup sync to the kernel. Refine some handling of fw/bl startup for all.	2007-11-27 01:20:26 +00:00
system-target.h	Enable dualcore for the pp5002 processor by adding the needed cache handling and sleep/wakeup sync to the kernel. Refine some handling of fw/bl startup for all.	2007-11-27 01:20:26 +00:00
usb-drv-pp502x.c	reset USB controller when entering USB test mode	2008-02-29 18:35:21 +00:00
usb-fw-pp502x.c	m:robe 100: add USB detection	2008-03-02 13:07:11 +00:00
usb-fw-pp5002.c
usb-target.h
wmcodec-pp.c	Commit FS#8379 by Andree Buschmann. Disables much of the remaining unneeded hardware on PP50xx targets (Ipods, Sansa, H10s, etc) resulting in a large savings in power and consequent increase in battery life. Results vary from target to target and from codec to codec, but we now approach the OF runtime on several PP devices. For now, leave base CPU clock at 30MHz, although further savings is possible with some codecs if clock is reduced. Additionally, fix battery capacity on c200 and use my measurements to improve runtime estimation for Sandisk targets.	2008-02-10 05:39:20 +00:00
wmcodec-telechips.c	Initial Cowon D2 commit:	2008-01-14 22:04:48 +00:00