/*************************************************************************** * __________ __ ___. * Open \______ \ ____ ____ | | _\_ |__ _______ ___ * Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ / * Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < < * Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \ * \/ \/ \/ \/ \/ * $Id$ * * Copyright © 2010 Amaury Pouly * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * as published by the Free Software Foundation; either version 2 * of the License, or (at your option) any later version. * * This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY * KIND, either express or implied. * ****************************************************************************/ #ifndef __USB_DRV_AS3525v2_H__ #define __USB_DRV_AS3525v2_H__ #include "as3525v2.h" /* All multi-bit fields in the driver use the following convention. * If the register name is NAME, then there is one define NAME_bitp * which holds the bit position and one define NAME_bits which holds * a mask of the bits within the register (after shift). * These macros allow easy access and construction of such fields */ /* Usage: * - extract(reg_name,field_name) * extract a field of the register * - bitm(reg_name,field_name) * build a bitmask for the field * - make(reg_name,field_name,value) * build the value of the field (doesn't mask) */ #define extract(reg_name, field_name) \ ((reg_name >> reg_name##_##field_name##_bitp) & reg_name##_##field_name##_bits) #define bitm(reg_name, field_name) \ (reg_name##_##field_name##_bits << reg_name##_##field_name##_bitp) #define USB_DEVICE (USB_BASE + 0x0800) /** USB Device base address */ /** * Core Global Registers */ #define BASE_REG(offset) (*(volatile unsigned long *)(USB_BASE + offset)) /** OTG Control and Status Register */ #define GOTGCTL BASE_REG(0x000) /** OTG Interrupt Register */ #define GOTGINT BASE_REG(0x004) /** Core AHB Configuration Register */ #define GAHBCFG BASE_REG(0x008) #define GAHBCFG_glblintrmsk (1 << 0) /** Global interrupt mask */ #define GAHBCFG_hburstlen_bitp 1 #define GAHBCFG_INT_DMA_BURST_SINGLE 0 #define GAHBCFG_INT_DMA_BURST_INCR 1 /** note: the linux patch has several other value, this is one picked for internal dma */ #define GAHBCFG_INT_DMA_BURST_INCR4 3 #define GAHBCFG_INT_DMA_BURST_INCR8 5 #define GAHBCFG_INT_DMA_BURST_INCR16 7 #define GAHBCFG_dma_enable (1 << 5) /** Enable DMA */ /** Core USB Configuration Register */ #define GUSBCFG BASE_REG(0x00C) #define GUSBCFG_toutcal_bitp 0 #define GUSBCFG_toutcal_bits 0x7 #define GUSBCFG_phy_if (1 << 3) /** select utmi bus width ? */ #define GUSBCFG_ulpi_utmi_sel (1 << 4) /** select ulpi:1 or utmi:0 */ #define GUSBCFG_fsintf (1 << 5) #define GUSBCFG_physel (1 << 6) #define GUSBCFG_ddrsel (1 << 7) #define GUSBCFG_srpcap (1 << 8) #define GUSBCFG_hnpcapp (1 << 9) #define GUSBCFG_usbtrdtim_bitp 10 #define GUSBCFG_usbtrdtim_bits 0xf #define GUSBCFG_nptxfrwnden (1 << 14) #define GUSBCFG_phylpwrclksel (1 << 15) #define GUSBCFG_otgutmifssel (1 << 16) #define GUSBCFG_ulpi_fsls (1 << 17) #define GUSBCFG_ulpi_auto_res (1 << 18) #define GUSBCFG_ulpi_clk_sus_m (1 << 19) #define GUSBCFG_ulpi_ext_vbus_drv (1 << 20) #define GUSBCFG_ulpi_int_vbus_indicator (1 << 21) #define GUSBCFG_term_sel_dl_pulse (1 << 22) #define GUSBCFG_force_host_mode (1 << 29) #define GUSBCFG_force_device_mode (1 << 30) #define GUSBCFG_corrupt_tx_packet (1 << 31) /** Core Reset Register */ #define GRSTCTL BASE_REG(0x010) #define GRSTCTL_csftrst (1 << 0) /** Core soft reset */ #define GRSTCTL_hsftrst (1 << 1) /** Hclk soft reset */ #define GRSTCTL_intknqflsh (1 << 3) /** In Token Sequence Learning Queue Flush */ #define GRSTCTL_rxfflsh_flush (1 << 4) /** RxFIFO Flush */ #define GRSTCTL_txfflsh_flush (1 << 5) /** TxFIFO Flush */ #define GRSTCTL_txfnum_bitp 6 /** TxFIFO Number */ #define GRSTCTL_txfnum_bits 0x1f #define GRSTCTL_ahbidle (1 << 31) /** AHB idle state*/ /** Core Interrupt Register */ #define GINTSTS BASE_REG(0x014) /* NOTE: GINTSTS bits are the same as in GINTMSK plus this one */ #define GINTSTS_curmode (1 << 0) /** Current mode, 0 for device */ /** Core Interrupt Mask Register */ #define GINTMSK BASE_REG(0x018) #define GINTMSK_modemismatch (1 << 1) /** mode mismatch ? */ #define GINTMSK_otgintr (1 << 2) #define GINTMSK_sofintr (1 << 3) #define GINTMSK_rxstsqlvl (1 << 4) #define GINTMSK_nptxfempty (1 << 5) /** Non-periodic TX fifo empty ? */ #define GINTMSK_ginnakeff (1 << 6) #define GINTMSK_goutnakeff (1 << 7) #define GINTMSK_i2cintr (1 << 9) #define GINTMSK_erlysuspend (1 << 10) #define GINTMSK_usbsuspend (1 << 11) /** USB suspend */ #define GINTMSK_usbreset (1 << 12) /** USB reset */ #define GINTMSK_enumdone (1 << 13) /** Enumeration done */ #define GINTMSK_isooutdrop (1 << 14) #define GINTMSK_eopframe (1 << 15) #define GINTMSK_epmismatch (1 << 17) /** endpoint mismatch ? */ #define GINTMSK_inepintr (1 << 18) /** in pending ? */ #define GINTMSK_outepintr (1 << 19) /** out pending ? */ #define GINTMSK_incomplisoin (1 << 20) /** ISP in complete ? */ #define GINTMSK_incomplisoout (1 << 21) /** ISO out complete ? */ #define GINTMSK_portintr (1 << 24) /** Port status change ? */ #define GINTMSK_hcintr (1 << 25) #define GINTMSK_ptxfempty (1 << 26) /** Periodic TX fifof empty ? */ #define GINTMSK_conidstschng (1 << 28) #define GINTMSK_disconnect (1 << 29) /** Disconnect */ #define GINTMSK_sessreqintr (1 << 30) /** Session request */ #define GINTMSK_wkupintr (1 << 31) /** Wake up */ /** Receive Status Debug Read Register (Read Only) */ #define GRXSTSR BASE_REG(0x01C) /** Receive Status Read /Pop Register (Read Only) */ #define GRXSTSP BASE_REG(0x020) /** Receive FIFO Size Register */ #define GRXFSIZ BASE_REG(0x024) /** Periodic Transmit FIFO Size Register */ #define GNPTXFSIZ BASE_REG(0x028) /** Non-Periodic Transmit FIFO/Queue Status Register */ #define GNPTXSTS BASE_REG(0x02C) /** I2C Access Register */ #define GI2CCTL BASE_REG(0x030) /** PHY Vendor Control Register */ #define GPVNDCTL BASE_REG(0x034) /** General Purpose Input/Output Register */ #define GGPIO BASE_REG(0x038) /** User ID Register */ #define GUID BASE_REG(0x03C) /** Synopsys ID Register */ #define GSNPSID BASE_REG(0x040) /** User HW Config1 Register */ #define GHWCFG1 BASE_REG(0x044) #define GHWCFG1_IN_EP(ep) (1 << (2 * (ep))) /** 1 if EP(ep) has in cap */ #define GHWCFG1_OUT_EP(ep) (1 << (1 + 2 * (ep))) /** same for out */ /** User HW Config2 Register */ #define GHWCFG2 BASE_REG(0x048) #define GHWCFG2_arch_bitp 3 /** Architecture */ #define GHWCFG2_arch_bits 0x3 #define GHWCFG2_hs_phy_type_bitp 6 /** High speed PHY type */ #define GHWCFG2_hs_phy_type_bits 0x3 #define GHWCFG2_fs_phy_type_bitp 8 /** Full speed PHY type */ #define GHWCFG2_fs_phy_type_bits 0x3 #define GHWCFG2_num_ep_bitp 10 /** Number of endpoints */ #define GHWCFG2_num_ep_bits 0xf #define GHWCFG2_dyn_fifo (1 << 19) /** Dynamic FIFO */ /* For GHWCFG2_HS_PHY_TYPE and GHWCFG2_FS_PHY_TYPE */ #define GHWCFG2_PHY_TYPE_UNSUPPORTED 0 #define GHWCFG2_PHY_TYPE_UTMI 1 #define GHWCFG2_ARCH_INTERNAL_DMA 2 /** User HW Config3 Register */ #define GHWCFG3 BASE_REG(0x04C) #define GHWCFG3_dfifo_len_bitp 16 /** Total fifo size */ #define GHWCFG3_dfifo_len_bits 0xffff /** User HW Config4 Register */ #define GHWCFG4 BASE_REG(0x050) #define GHWCFG4_utmi_phy_data_width_bitp 14 /** UTMI+ data bus width */ #define GHWCFG4_utmi_phy_data_width_bits 0x3 #define GHWCFG4_ded_fifo_en (1 << 25) /** Dedicated Tx FIFOs */ #define GHWCFG4_num_in_ep_bitp 26 /** Number of IN endpoints */ #define GHWCFG4_num_in_ep_bits 0xf /* 1<=ep<=15, don't use ep=0 !!! */ /** Device IN Endpoint Transmit FIFO (ep) Size Register */ #define DIEPTXFSIZ(ep) BASE_REG(0x100 + 4 * (ep)) /** Build the content of a FIFO size register like DIEPTXFSIZ(i) and GNPTXFSIZ*/ #define MAKE_FIFOSIZE_DATA(startadr, depth) \ (((startadr) & 0xffff) | ((depth) << 16)) /** Retrieve fifo size for such registers */ #define GET_FIFOSIZE_DEPTH(data) \ ((data) >> 16) /** Retrieve fifo start address for such registers */ #define GET_FIFOSIZE_START_ADR(data) \ ((data) & 0xffff) /** * Device Registers Base Addresses */ #define DEV_REG(offset) (*(volatile unsigned long *)(USB_DEVICE + offset)) /** Device Configuration Register */ #define DCFG DEV_REG(0x00) #define DCFG_devspd_bitp 0 /** Device Speed */ #define DCFG_devspd_bits 0x3 #define DCFG_devspd_hs_phy_hs 0 /** High speed PHY running at high speed */ #define DCFG_devspd_hs_phy_fs 1 /** High speed PHY running at full speed */ #define DCFG_nzstsouthshk (1 << 2) /** Non Zero Length Status OUT Handshake */ #define DCFG_devadr_bitp 4 /** Device Address */ #define DCFG_devadr_bits 0x7f #define DCFG_perfrint_bitp 11 /** Periodic Frame Interval */ #define DCFG_perfrint_bits 0x3 #define DCFG_FRAME_INTERVAL_80 0 #define DCFG_FRAME_INTERVAL_85 1 #define DCFG_FRAME_INTERVAL_90 2 #define DCFG_FRAME_INTERVAL_95 3 /** Device Control Register */ #define DCTL DEV_REG(0x04) #define DCTL_rmtwkupsig (1 << 0) /** Remote Wakeup */ #define DCTL_sftdiscon (1 << 1) /** Soft Disconnect */ #define DCTL_gnpinnaksts (1 << 2) /** Global Non-Periodic IN NAK Status */ #define DCTL_goutnaksts (1 << 3) /** Global OUT NAK Status */ #define DCTL_tstctl_bitp 4 /** Test Control */ #define DCTL_tstctl_bits 0x7 #define DCTL_sgnpinnak (1 << 7) /** Set Global Non-Periodic IN NAK */ #define DCTL_cgnpinnak (1 << 8) /** Clear Global Non-Periodic IN NAK */ #define DCTL_sgoutnak (1 << 9) /** Set Global OUT NAK */ #define DCTL_cgoutnak (1 << 10) /** Clear Global OUT NAK */ /* "documented" in constants.h only */ #define DCTL_pwronprgdone (1 << 11) /** Power on Program Done ? */ /** Device Status Register */ #define DSTS DEV_REG(0x08) #define DSTS_suspsts (1 << 0) /** Suspend status */ #define DSTS_enumspd_bitp 1 /** Enumerated speed */ #define DSTS_enumspd_bits 0x3 #define DSTS_ENUMSPD_HS_PHY_30MHZ_OR_60MHZ 0 #define DSTS_ENUMSPD_FS_PHY_30MHZ_OR_60MHZ 1 #define DSTS_ENUMSPD_LS_PHY_6MHZ 2 #define DSTS_ENUMSPD_FS_PHY_48MHZ 3 #define DSTS_errticerr (1 << 3) /** Erratic errors ? */ #define DSTS_soffn_bitp 7 /** Frame or Microframe Number of the received SOF */ #define DSTS_soffn_bits 0x3fff /** Device IN Endpoint Common Interrupt Mask Register */ #define DIEPMSK DEV_REG(0x10) /* the following apply to DIEPMSK and DIEPINT */ #define DIEPINT_xfercompl (1 << 0) /** Transfer complete */ #define DIEPINT_epdisabled (1 << 1) /** Endpoint disabled */ #define DIEPINT_ahberr (1 << 2) /** AHB error */ #define DIEPINT_timeout (1 << 3) /** Timeout handshake (non-iso TX) */ #define DIEPINT_intktxfemp (1 << 4) /** IN token received with tx fifo empty */ #define DIEPINT_intknepmis (1 << 5) /** IN token received with ep mismatch */ #define DIEPINT_inepnakeff (1 << 6) /** IN endpoint NAK effective */ #define DIEPINT_emptyintr (1 << 7) /** linux doc broken on this, empty fifo ? */ #define DIEPINT_txfifoundrn (1 << 8) /** linux doc void on this, tx fifo underrun ? */ /** Device OUT Endpoint Common Interrupt Mask Register */ #define DOEPMSK DEV_REG(0x14) /* the following apply to DOEPMSK and DOEPINT */ #define DOEPINT_xfercompl (1 << 0) /** Transfer complete */ #define DOEPINT_epdisabled (1 << 1) /** Endpoint disabled */ #define DOEPINT_ahberr (1 << 2) /** AHB error */ #define DOEPINT_setup (1 << 3) /** Setup Phase Done (control EPs)*/ /** Device All Endpoints Interrupt Register */ #define DAINT DEV_REG(0x18) /* valid for DAINT and DAINTMSK, for 0<=ep<=15 */ #define DAINT_IN_EP(i) (1 << (i)) #define DAINT_OUT_EP(i) (1 << ((i) + 16)) /** Device Endpoints Interrupt Mask Register */ #define DAINTMSK DEV_REG(0x1C) /** Device IN Token Sequence Learning Queue Read Register 1 */ #define DTKNQR1 DEV_REG(0x20) /** Device IN Token Sequence Learning Queue Register 2 */ #define DTKNQR2 DEV_REG(0x24) /** Device IN Token Queue Pop register */ #define DTKNQP DEV_REG(0x28) /* fixme: those registers are not present in registers.h but are in dwc_otgh_regs.h. * the previous registers exists but has a different name :( */ /** Device VBUS discharge register*/ #define DVBUSDIS DEV_REG(0x28) /** Device VBUS pulse register */ #define DVBUSPULSE DEV_REG(0x2C) /** Device IN Token Queue Read Register 3 (RO) */ #define DTKNQR3 DEV_REG(0x30) /** Device Thresholding control register */ #define DTHRCTL DEV_REG(0x30) #define DTHRCTL_non_iso_thr_en (1 << 0) #define DTHRCTL_iso_thr_en (1 << 1) #define DTHRCTL_tx_thr_len_bitp 2 #define DTHRCTL_tx_thr_len_bits 0x1FF #define DTHRCTL_rx_thr_en (1 << 16) #define DTHRCTL_rx_thr_len_bitp 17 #define DTHRCTL_rx_thr_len_bits 0x1FF /** Device IN Token Queue Read Register 4 (RO) */ #define DTKNQR4 DEV_REG(0x34) /** Device IN EPs empty Inr. Mask Register */ #define FFEMPTYMSK DEV_REG(0x34) /* 0<=ep<=15, you can use ep=0 */ /** Device IN Endpoint (ep) Control Register */ #define DIEPCTL(ep) DEV_REG(0x100 + (ep) * 0x20) /** Device IN Endpoint (ep) Interrupt Register */ #define DIEPINT(ep) DEV_REG(0x100 + (ep) * 0x20 + 0x8) /** Device IN Endpoint (ep) Transfer Size Register */ #define DIEPTSIZ(ep) DEV_REG(0x100 + (ep) * 0x20 + 0x10) /** Device IN Endpoint (ep) DMA Address Register */ #define DIEPDMA(ep) DEV_REG(0x100 + (ep) * 0x20 + 0x14) /** Device IN Endpoint (ep) Transmit FIFO Status Register */ #define DTXFSTS(ep) DEV_REG(0x100 + (ep) * 0x20 + 0x18) /* 0<=ep<=15, you can use ep=0 */ /** Device OUT Endpoint (ep) Control Register */ #define DOEPCTL(ep) DEV_REG(0x300 + (ep) * 0x20) /** Device OUT Endpoint (ep) Frame number Register */ #define DOEPFN(ep) DEV_REG(0x300 + (ep) * 0x20 + 0x4) /** Device Endpoint (ep) Interrupt Register */ #define DOEPINT(ep) DEV_REG(0x300 + (ep) * 0x20 + 0x8) /** Device OUT Endpoint (ep) Transfer Size Register */ #define DOEPTSIZ(ep) DEV_REG(0x300 + (ep) * 0x20 + 0x10) /** Device Endpoint (ep) DMA Address Register */ #define DOEPDMA(ep) DEV_REG(0x300 + (ep) * 0x20 + 0x14) #define PCGCCTL BASE_REG(0xE00) /** Power and Clock Gating Control Register */ /** Maximum Packet Size * IN/OUT EPn * IN/OUT EP0 - 2 bits * 2'b00: 64 Bytes * 2'b01: 32 * 2'b10: 16 * 2'b11: 8 */ #define DEPCTL_mps_bitp 0 #define DEPCTL_mps_bits 0x7ff #define DEPCTL_MPS_64 0 #define DEPCTL_MPS_32 1 #define DEPCTL_MPS_16 2 #define DEPCTL_MPS_8 3 /** Next Endpoint * IN EPn/IN EP0 * OUT EPn/OUT EP0 - reserved */ #define DEPCTL_nextep_bitp 11 #define DEPCTL_nextep_bits 0xf #define DEPCTL_usbactep (1 << 15) /** USB Active Endpoint */ /** Endpoint DPID (INTR/Bulk IN and OUT endpoints) * This field contains the PID of the packet going to * be received or transmitted on this endpoint. The * application should program the PID of the first * packet going to be received or transmitted on this * endpoint , after the endpoint is * activated. Application use the SetD1PID and * SetD0PID fields of this register to program either * D0 or D1 PID. * * The encoding for this field is * - 0: D0 * - 1: D1 */ #define DEPCTL_dpid (1 << 16) #define DEPCTL_naksts (1 << 17) /** NAK Status */ /** Endpoint Type * 2'b00: Control * 2'b01: Isochronous * 2'b10: Bulk * 2'b11: Interrupt */ #define DEPCTL_eptype_bitp 18 #define DEPCTL_eptype_bits 0x3 /** Snoop Mode * OUT EPn/OUT EP0 * IN EPn/IN EP0 - reserved */ #define DEPCTL_snp (1 << 20) #define DEPCTL_stall (1 << 21) /** Stall Handshake */ /** Tx Fifo Number * IN EPn/IN EP0 * OUT EPn/OUT EP0 - reserved */ #define DEPCTL_txfnum_bitp 22 #define DEPCTL_txfnum_bits 0xf #define DEPCTL_cnak (1 << 26) /** Clear NAK */ #define DEPCTL_snak (1 << 27) /** Set NAK */ /** Set DATA0 PID (INTR/Bulk IN and OUT endpoints) * Writing to this field sets the Endpoint DPID (DPID) * field in this register to DATA0. Set Even * (micro)frame (SetEvenFr) (ISO IN and OUT Endpoints) * Writing to this field sets the Even/Odd * (micro)frame (EO_FrNum) field to even (micro) * frame. */ #define DEPCTL_setd0pid (1 << 28) /** Set DATA1 PID (INTR/Bulk IN and OUT endpoints) * Writing to this field sets the Endpoint DPID (DPID) * field in this register to DATA1 Set Odd * (micro)frame (SetOddFr) (ISO IN and OUT Endpoints) * Writing to this field sets the Even/Odd * (micro)frame (EO_FrNum) field to odd (micro) frame. */ #define DEPCTL_setd1pid (1 << 29) #define DEPCTL_epdis (1 << 30) /** Endpoint disable */ #define DEPCTL_epena (1 << 31) /** Endpoint enable */ /* valid for any D{I,O}EPTSIZi with 1<=i<=15, NOT for i=0 ! */ #define DEPTSIZ_xfersize_bits 0x7ffff /** Transfer Size */ #define DEPTSIZ_pkcnt_bitp 19 /** Packet Count */ #define DEPTSIZ_pkcnt_bits 0x3ff #define DEPTSIZ_mc_bitp 29 /** Multi Count - Periodic IN endpoints */ #define DEPTSIZ_mc_bits 0x3 /* idem but for i=0 */ #define DEPTSIZ0_xfersize_bits 0x7f /** Transfer Size */ #define DEPTSIZ0_pkcnt_bitp 19 /** Packet Count */ #define DEPTSIZ0_pkcnt_bits 0x1 #define DEPTSIZ0_supcnt_bitp 29 /** Setup Packet Count (DOEPTSIZ0 Only) */ #define DEPTSIZ0_supcnt_bits 0x3 /** * Parameters */ #define USE_CUSTOM_FIFO_LAYOUT #ifdef USE_CUSTOM_FIFO_LAYOUT /* Data fifo: includes RX fifo, non period TX fifo and periodic fifos * NOTE: this is a hardware parameter, it cannot be changed ! */ #define DATA_FIFO_DEPTH 0x535 /* size of the FX fifo */ #define RX_FIFO_SIZE 0x100 /* size of the non periodic TX fifo */ #define NPTX_FIFO_SIZE 0x100 /* size of each TX ep fifo size */ #define EPTX_FIFO_SIZE 0x100 #endif /* USE_CUSTOM_FIFO_LAYOUT */ /* Number of IN/OUT endpoints */ #define NUM_IN_EP 3 #define NUM_OUT_EP 2 /* List of IN enpoints */ #define IN_EP_LIST 1, 3, 5 #define OUT_EP_LIST 2, 4 #endif /* __USB_DRV_AS3525v2_H__ */