/*************************************************************************** * __________ __ ___. * Open \______ \ ____ ____ | | _\_ |__ _______ ___ * Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ / * Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < < * Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \ * \/ \/ \/ \/ \/ * $Id$ * * Copyright (C) 2007 by Rob Purchase * Copyright © 2008 Rafaël Carré * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * as published by the Free Software Foundation; either version 2 * of the License, or (at your option) any later version. * * This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY * KIND, either express or implied. * ****************************************************************************/ #include "config.h" #include "kernel.h" #include "system.h" #include "panic.h" #include "ascodec.h" #include "adc.h" #include "dma-target.h" #include "clock-target.h" #include "fmradio_i2c.h" #include "button.h" #include "backlight-target.h" #include "lcd.h" /* Charge Pump and Power management Settings */ #define AS314_CP_DCDC3_SETTING \ ((0<<7) | /* CP_SW Auto-Switch Margin 0=200/300 1=150/255 */ \ (0<<6) | /* CP_on 0=Normal op 1=Chg Pump Always On */ \ (0<<5) | /* LREG_CPnot Always write 0 */ \ (0<<3) | /* DCDC3p BVDD setting 3.6/3.2/3.1/3.0 */ \ (1<<2) | /* LREG_off 1=Auto mode switching 0=Length Reg only*/\ (0<<0) ) /* CVDDp Core Voltage Setting 1.2/1.15/1.10/1.05*/ #define CVDD_1_20 0 #define CVDD_1_15 1 #define CVDD_1_10 2 #define CVDD_1_05 3 #define default_interrupt(name) \ extern __attribute__((weak,alias("UIRQ"))) void name (void) static void UIRQ (void) __attribute__((interrupt ("IRQ"))); void irq_handler(void) __attribute__((naked, interrupt ("IRQ"))); void fiq_handler(void) __attribute__((interrupt ("FIQ"))); default_interrupt(INT_WATCHDOG); default_interrupt(INT_TIMER1); default_interrupt(INT_TIMER2); default_interrupt(INT_USB_FUNC); default_interrupt(INT_DMAC); default_interrupt(INT_NAND); default_interrupt(INT_IDE); default_interrupt(INT_MCI0); default_interrupt(INT_MCI1); default_interrupt(INT_AUDIO); default_interrupt(INT_SSP); default_interrupt(INT_I2C_MS); default_interrupt(INT_I2C_AUDIO); default_interrupt(INT_I2SIN); default_interrupt(INT_I2SOUT); default_interrupt(INT_UART); default_interrupt(INT_GPIOD); default_interrupt(RESERVED1); /* Interrupt 17 : unused */ default_interrupt(INT_CGU); default_interrupt(INT_MEMORY_STICK); default_interrupt(INT_DBOP); default_interrupt(RESERVED2); /* Interrupt 21 : unused */ default_interrupt(RESERVED3); /* Interrupt 22 : unused */ default_interrupt(RESERVED4); /* Interrupt 23 : unused */ default_interrupt(RESERVED5); /* Interrupt 24 : unused */ default_interrupt(RESERVED6); /* Interrupt 25 : unused */ default_interrupt(RESERVED7); /* Interrupt 26 : unused */ default_interrupt(RESERVED8); /* Interrupt 27 : unused */ default_interrupt(RESERVED9); /* Interrupt 28 : unused */ /* INT_GPIOA is declared in this file */ void INT_GPIOA(void); default_interrupt(INT_GPIOB); default_interrupt(INT_GPIOC); static const char * const irqname[] = { "INT_WATCHDOG", "INT_TIMER1", "INT_TIMER2", "INT_USB", "INT_DMAC", "INT_NAND", "INT_IDE", "INT_MCI0", "INT_MCI1", "INT_AUDIO", "INT_SSP", "INT_I2C_MS", "INT_I2C_AUDIO", "INT_I2SIN", "INT_I2SOUT", "INT_UART", "INT_GPIOD", "RESERVED1", "INT_CGU", "INT_MEMORY_STICK", "INT_DBOP", "RESERVED2", "RESERVED3", "RESERVED4", "RESERVED5", "RESERVED6", "RESERVED7", "RESERVED8", "RESERVED9", "INT_GPIOA", "INT_GPIOB", "INT_GPIOC" }; static void UIRQ(void) { bool masked = false; int status = VIC_IRQ_STATUS; if(status == 0) { status = VIC_RAW_INTR; /* masked interrupts */ masked = true; } if(status == 0) panicf("Unhandled IRQ (source unknown!)"); unsigned irq_no = 31 - __builtin_clz(status); panicf("Unhandled %smasked IRQ %02X: %s (status 0x%8X)", masked ? "" : "un", irq_no, irqname[irq_no], status); } /* Vectored interrupts (16 available) */ static const struct { int source; void (*isr) (void); } vec_int_srcs[] = { /* Highest priority at the top of the list */ #if defined(HAVE_HOTSWAP) || defined(HAVE_RDS_CAP) || \ (defined(SANSA_FUZEV2) && !INCREASED_SCROLLWHEEL_POLLING) /* If GPIOA ISR is interrupted, things seem to go wonky ?? */ { INT_SRC_GPIOA, INT_GPIOA }, #endif #ifdef HAVE_RECORDING { INT_SRC_I2SIN, INT_I2SIN }, /* For recording */ #endif { INT_SRC_DMAC, INT_DMAC }, /* Playback follows recording */ { INT_SRC_NAND, INT_NAND }, #if (defined HAVE_MULTIDRIVE && CONFIG_CPU == AS3525) { INT_SRC_MCI0, INT_MCI0 }, #endif { INT_SRC_USB, INT_USB_FUNC, }, { INT_SRC_TIMER1, INT_TIMER1 }, { INT_SRC_TIMER2, INT_TIMER2 }, { INT_SRC_I2C_AUDIO, INT_I2C_AUDIO }, { INT_SRC_AUDIO, INT_AUDIO }, /* Lowest priority at the end of the list */ }; static void setup_vic(void) { CGU_PERI |= CGU_VIC_CLOCK_ENABLE; /* enable VIC */ VIC_INT_EN_CLEAR = 0xffffffff; /* disable all interrupt lines */ VIC_INT_SELECT = 0; /* only IRQ, no FIQ */ *VIC_DEF_VECT_ADDR = UIRQ; for(unsigned int i = 0; i < ARRAYLEN(vec_int_srcs); i++) { VIC_VECT_ADDRS[i] = vec_int_srcs[i].isr; VIC_VECT_CNTLS[i] = (1<<5) | vec_int_srcs[i].source; } /* Reset priority hardware */ for(unsigned int i = 0; i < 32; i++) *VIC_VECT_ADDR = 0; } void INT_GPIOA(void) { #ifdef HAVE_HOTSWAP void sd_gpioa_isr(void); sd_gpioa_isr(); #endif #if defined(SANSA_FUZEV2) && !INCREASED_SCROLLWHEEL_POLLING void button_gpioa_isr(void); button_gpioa_isr(); #endif #ifdef HAVE_RDS_CAP void tuner_isr(void); tuner_isr(); #endif } void irq_handler(void) { /* Worst-case IRQ stack usage with 10 vectors: * 10*4*10 = 400 bytes (100 words) * * No SVC stack is used by pro/epi-logue code */ asm volatile ( "sub lr, lr, #4 \n" /* Create return address */ "stmfd sp!, { r0-r5, r12, lr } \n" /* Save what gets clobbered */ "ldr r0, =0xc6010030 \n" /* Obtain VIC address (before SPSR read!) */ "ldr r12, [r0] \n" /* Load Vector */ "mrs r1, spsr \n" /* Save SPSR_irq */ "stmfd sp!, { r0-r1 } \n" /* Must have something bet. mrs and msr */ "msr cpsr_c, #0x13 \n" /* Switch to SVC mode, enable IRQ */ "and r4, sp, #4 \n" /* Align SVC stack to 8 bytes, save */ "sub sp, sp, r4 \n" "mov r5, lr \n" /* Save lr_SVC */ #if ARM_ARCH >= 5 "blx r12 \n" /* Call handler */ #else "mov lr, pc \n" "bx r12 \n" #endif "add sp, sp, r4 \n" /* Undo alignment fudge */ "mov lr, r5 \n" /* Restore lr_SVC */ "msr cpsr_c, #0x92 \n" /* Mask IRQ, return to IRQ mode */ "ldmfd sp!, { r0-r1 } \n" /* Pop VIC address, SPSR_irq */ "str r0, [r0] \n" /* Ack end of ISR to VIC */ "msr spsr_cxsf, r1 \n" /* Restore SPSR_irq */ "ldmfd sp!, { r0-r5, r12, pc }^ \n" /* Restore regs, and RFE */ ); } void fiq_handler(void) { } #if defined(SANSA_C200V2) int c200v2_variant; static void check_model_variant(void) { unsigned int i; unsigned int saved_dir = GPIOA_DIR; /* Make A7 input */ GPIOA_DIR &= ~(1<<7); /* wait a little to allow the pullup/pulldown resistor * to charge the input capacitance */ for (i=0; i<1000; i++) asm volatile ("nop\n"); /* read the pullup/pulldown value on A7 to determine the variant */ c200v2_variant = !GPIOA_PIN(7); GPIOA_DIR = saved_dir; } #elif defined(SANSA_FUZEV2) || defined(SANSA_CLIPPLUS) || defined(SANSA_CLIPZIP) int amsv2_variant; static void check_model_variant(void) { GPIOB_DIR &= ~(1<<5); amsv2_variant = !!GPIOB_PIN(5); } #else static inline void check_model_variant(void) { } #endif /* model selection */ void system_init(void) { #if CONFIG_CPU == AS3525v2 CCU_SRC = 0x57D7BF0; #else CCU_SRC = 0x1fffff0 & ~CCU_SRC_IDE_EN; /* FIXME */ #endif unsigned int reset_loops = 640; while(reset_loops--) CCU_SRL = CCU_SRL_MAGIC_NUMBER; CCU_SRC = CCU_SRL = 0; CCU_SCON = 1; /* AHB master's priority configuration : TIC (Test Interface Controller) > DMA > USB > IDE > ARM */ CGU_PROC = 0; /* fclk 24 MHz */ #if CONFIG_CPU == AS3525v2 /* pclk is always based on PLLA, since we don't know the current PLLA speed, * avoid having pclk too fast and hope it's not too low */ CGU_PERI |= 0xf << 2; /* pclk lowest */ #else CGU_PERI &= ~0x7f; /* pclk 24 MHz */ #endif CGU_PERI &= ~CGU_ROM_ENABLE; /*disable built in boot rom clock*/ /* bits 31:30 should be set to 0 in arm926-ejs */ asm volatile( "mrc p15, 0, r0, c1, c0 \n" /* control register */ "bic r0, r0, #3<<30 \n" /* clears bus bits : sets fastbus */ "mcr p15, 0, r0, c1, c0 \n" : : : "r0" ); CGU_COUNTA = CGU_LOCK_CNT; CGU_PLLA = AS3525_PLLA_SETTING; CGU_PLLASUP = 0; /* enable PLLA */ while(!(CGU_INTCTRL & CGU_PLLA_LOCK)); /* wait until PLLA is locked */ #if AS3525_MCLK_SEL == AS3525_CLK_PLLB CGU_COUNTB = CGU_LOCK_CNT; CGU_PLLB = AS3525_PLLB_SETTING; CGU_PLLBSUP = 0; /* enable PLLB */ while(!(CGU_INTCTRL & CGU_PLLB_LOCK)); /* wait until PLLB is locked */ #endif /* Set FCLK frequency */ CGU_PROC = ((AS3525_FCLK_POSTDIV << 4) | (AS3525_FCLK_PREDIV << 2) | AS3525_FCLK_SEL); /* Set PCLK frequency */ CGU_PERI = ((CGU_PERI & ~0x7F) | /* reset divider & clksel bits */ (AS3525_PCLK_DIV0 << 2) | #if CONFIG_CPU == AS3525 (AS3525_PCLK_DIV1 << 6) | #endif AS3525_PCLK_SEL); set_cpu_frequency(CPUFREQ_DEFAULT); #if 0 /* the GPIO clock is already enabled by the dualboot function */ CGU_PERI |= CGU_GPIO_CLOCK_ENABLE; #endif /* enable timer interface for TIMER1 & TIMER2 */ CGU_PERI |= CGU_TIMERIF_CLOCK_ENABLE; setup_vic(); dma_init(); ascodec_init(); /* Initialize power management settings */ #ifdef HAVE_AS3543 /* PLL: disable audio PLL, we use MCLK already */ ascodec_write_pmu(0x1A, 7, 0x02); /* DCDC_Cntr: set switching speed of CVDD1/2 power supplies to 1 MHz */ ascodec_write_pmu(0x17, 7, 0x30); /* Out_Cntr2: set drive strength of 24 MHz and 32 kHz clocks to 1 mA */ ascodec_write_pmu(0x1A, 2, 0xCC); /* CHGVBUS2: set VBUS threshold to 3.18V and EOC threshold to 30% CC */ ascodec_write_pmu(0x19, 2, 0x41); /* PVDD1: set PVDD1 power supply to 2.5 V */ ascodec_write_pmu(0x18, 1, 0x35); /* AVDD17: set AVDD17 power supply to 2.5V */ ascodec_write_pmu(0x18, 7, 0x31); #ifdef SANSA_CLIPZIP /* CVDD2: set CVDD2 power supply to 2.8V */ ascodec_write_pmu(0x17, 2, 0xF4); #endif #else /* HAVE_AS3543 */ ascodec_write(AS3514_CVDD_DCDC3, AS314_CP_DCDC3_SETTING); #endif /* HAVE_AS3543 */ #ifndef BOOTLOADER /* setup isr for microsd monitoring and for fuzev2 scrollwheel irq */ #if defined(HAVE_HOTSWAP) || \ (defined(SANSA_FUZEV2) && !INCREASED_SCROLLWHEEL_POLLING) VIC_INT_ENABLE = (INTERRUPT_GPIOA); /* pin selection for irq happens in the drivers */ #endif #if CONFIG_TUNER fmradio_i2c_init(); #endif #endif /* !BOOTLOADER */ check_model_variant(); } void system_reboot(void) { _backlight_off(); disable_irq(); /* re-enable internal ROM */ CGU_PERI |= CGU_ROM_ENABLE; /* use watchdog to reset */ CGU_PERI |= (CGU_WDOCNT_CLOCK_ENABLE | CGU_WDOIF_CLOCK_ENABLE); WDT_LOAD = 1; /* set counter to 1 */ WDT_CONTROL = 3; /* enable watchdog counter & reset */ while(1); } void system_exception_wait(void) { /* make sure lcd+backlight are on */ _backlight_panic_on(); /* make sure screen content is up to date */ lcd_update(); /* wait until button release (if a button is pressed) */ while(button_read_device()); /* then wait until next button press */ while(!button_read_device()); } int system_memory_guard(int newmode) { (void)newmode; return 0; } /* usecs may be at most 2^32/248 (17 seconds) for 248MHz max cpu freq */ void udelay(unsigned usecs) { unsigned cycles_per_usec; unsigned delay; if (cpu_frequency == CPUFREQ_MAX) { cycles_per_usec = (CPUFREQ_MAX + 999999) / 1000000; } else { cycles_per_usec = (CPUFREQ_NORMAL + 999999) / 1000000; } delay = (usecs * cycles_per_usec + 3) / 4; asm volatile( "1: subs %0, %0, #1 \n" /* 1 cycle */ " bne 1b \n" /* 3 cycles */ : : "r"(delay) ); } #ifndef BOOTLOADER #ifdef HAVE_ADJUSTABLE_CPU_FREQ #if CONFIG_CPU == AS3525 void set_cpu_frequency(long frequency) { if(frequency == CPUFREQ_MAX) { #ifdef HAVE_ADJUSTABLE_CPU_VOLTAGE /* Increasing frequency so boost voltage before change */ ascodec_write(AS3514_CVDD_DCDC3, (AS314_CP_DCDC3_SETTING | CVDD_1_20)); /* Some players run a bit low so use 1.175 volts instead of 1.20 */ /* Wait for voltage to be at least 1.175v before making fclk > 200 MHz */ while(adc_read(ADC_CVDD) < 470); /* 470 * .0025 = 1.175V */ #endif /* HAVE_ADJUSTABLE_CPU_VOLTAGE */ CGU_PROC = ((AS3525_FCLK_POSTDIV << 4) | (AS3525_FCLK_PREDIV << 2) | AS3525_FCLK_SEL); asm volatile( "mrc p15, 0, r0, c1, c0 \n" "orr r0, r0, #3<<30 \n" /* asynchronous bus clocking */ /* synchronous bus clocking had issues on some players */ "mcr p15, 0, r0, c1, c0 \n" : : : "r0" ); cpu_frequency = CPUFREQ_MAX; } else { asm volatile( "mrc p15, 0, r0, c1, c0 \n" "bic r0, r0, #3<<30 \n" /* fastbus clocking */ "mcr p15, 0, r0, c1, c0 \n" : : : "r0" ); /* FCLK is unused so put it to the lowest freq we can */ CGU_PROC = ((0xf << 4) | (0x3 << 2) | AS3525_CLK_MAIN); #ifdef HAVE_ADJUSTABLE_CPU_VOLTAGE /* Decreasing frequency so reduce voltage after change */ ascodec_write(AS3514_CVDD_DCDC3, (AS314_CP_DCDC3_SETTING | CVDD_1_10)); #endif /* HAVE_ADJUSTABLE_CPU_VOLTAGE */ cpu_frequency = CPUFREQ_NORMAL; } } #else /* as3525v2 */ /* FIXME : disabled for now, seems to cause buggy memory accesses * Disabling MMU or putting the function in uncached memory seems to help? */ void set_cpu_frequency(long frequency) { int oldstatus = disable_irq_save(); /* We only have 2 settings */ cpu_frequency = (frequency == CPUFREQ_MAX) ? frequency : CPUFREQ_NORMAL; if(frequency == CPUFREQ_MAX) { /* Change PCLK while FCLK is low, so it doesn't go too high */ CGU_PERI = (CGU_PERI & ~(0xF << 2)) | (AS3525_PCLK_DIV0 << 2); CGU_PROC = ((AS3525_FCLK_POSTDIV << 4) | (AS3525_FCLK_PREDIV << 2) | AS3525_FCLK_SEL); } else { CGU_PROC = ((AS3525_FCLK_POSTDIV_UNBOOSTED << 4) | (AS3525_FCLK_PREDIV << 2) | AS3525_FCLK_SEL); /* Change PCLK after FCLK is low, so it doesn't go too high */ CGU_PERI = (CGU_PERI & ~(0xF << 2)) | (AS3525_PCLK_DIV0_UNBOOSTED << 2); } restore_irq(oldstatus); } #endif #endif /* HAVE_ADJUSTABLE_CPU_FREQ */ #endif /* !BOOTLOADER */