/*************************************************************************** * __________ __ ___. * Open \______ \ ____ ____ | | _\_ |__ _______ ___ * Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ / * Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < < * Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \ * \/ \/ \/ \/ \/ * $Id$ * * Copyright (C) 2007 by Mark Arigo * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * as published by the Free Software Foundation; either version 2 * of the License, or (at your option) any later version. * * This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY * KIND, either express or implied. * ****************************************************************************/ #include #include "config.h" #include "cpu.h" #include "lcd.h" #include "kernel.h" #include "system.h" #ifdef SANSA_C200V2 #include "dbop-as3525.h" #endif /* Display status */ #if MEMORYSIZE > 2 static unsigned lcd_yuv_options SHAREDBSS_ATTR = 0; #endif static bool is_lcd_enabled = true; /* LCD command set for Samsung S6B33B2 */ #define R_NOP 0x00 #define R_OSCILLATION_MODE 0x02 #define R_DRIVER_OUTPUT_MODE 0x10 #define R_DCDC_SET 0x20 #define R_BIAS_SET 0x22 #define R_DCDC_CLOCK_DIV 0x24 #define R_DCDC_AMP_ONOFF 0x26 #define R_TEMP_COMPENSATION 0x28 #define R_CONTRAST_CONTROL1 0x2a #define R_CONTRAST_CONTROL2 0x2b #define R_STANDBY_OFF 0x2c #define R_STANDBY_ON 0x2d #define R_DDRAM_BURST_OFF 0x2e #define R_DDRAM_BURST_ON 0x2f #define R_ADDRESSING_MODE 0x30 #define R_ROW_VECTOR_MODE 0x32 #define R_N_LINE_INVERSION 0x34 #define R_FRAME_FREQ_CONTROL 0x36 #define R_RED_PALETTE 0x38 #define R_GREEN_PALETTE 0x3a #define R_BLUE_PALETTE 0x3c #define R_ENTRY_MODE 0x40 #define R_X_ADDR_AREA 0x42 #define R_Y_ADDR_AREA 0x43 #define R_RAM_SKIP_AREA 0x45 #define R_DISPLAY_OFF 0x50 #define R_DISPLAY_ON 0x51 #define R_SPEC_DISPLAY_PATTERN 0x53 #define R_PARTIAL_DISPLAY_MODE 0x55 #define R_PARTIAL_START_LINE 0x56 #define R_PARTIAL_END_LINE 0x57 #define R_AREA_SCROLL_MODE 0x59 #define R_SCROLL_START_LINE 0x5a #define R_DATA_FORMAT_SELECT 0x60 #if defined(SANSA_C200) /* wait for LCD */ static inline void lcd_wait_write(void) { while (LCD1_CONTROL & LCD1_BUSY_MASK); } /* send LCD data */ static void lcd_send_pixel(const fb_data data) { lcd_wait_write(); LCD1_DATA = data >> 8; lcd_wait_write(); LCD1_DATA = data & 0xff; } inline void lcd_write_data(const fb_data *data, int width) { do { lcd_send_pixel(*data++); } while(--width); } /* send LCD command */ static void lcd_send_command(unsigned char cmd, unsigned char arg) { lcd_wait_write(); LCD1_CMD = cmd; /* if the argument is 0, we send a NOP (= 0) command */ lcd_wait_write(); LCD1_CMD = arg; } static inline void c200v1_lcd_init(void) { /* This is from the c200 of bootloader beginning at offset 0xbbf4 */ outl(inl(0x70000010) & ~0xfc000000, 0x70000010); outl(inl(0x70000010), 0x70000010); DEV_INIT2 &= ~0x400; udelay(10000); LCD1_CONTROL &= ~0x4; udelay(15); LCD1_CONTROL |= 0x4; udelay(10); LCD1_CONTROL = 0x0084; /* bits (9,10) = 00 -> fastest setting */ udelay(10000); } #define lcd_delay(delay) udelay((delay) * 1000) #elif defined(SANSA_C200V2) static inline void lcd_delay(int delay) { //TUNEME : delay is in milliseconds delay <<= 14; while(delay--) ; } /* send LCD data */ void lcd_write_data(const fb_data *data, int width) { do { DBOP_DOUT = *data << 8 | *data >> 8; data++; /* Wait if push fifo is full */ while ((DBOP_STAT & (1<<6)) != 0); } while(--width); /* While push fifo is not empty */ while ((DBOP_STAT & (1<<10)) == 0); } /* send LCD command */ static void lcd_send_command(unsigned char cmd, unsigned char val) { DBOP_TIMPOL_23 = 0xa167006e; DBOP_DOUT = cmd | val << 8; while ((DBOP_STAT & (1<<10)) == 0); DBOP_TIMPOL_23 = 0xa167e06f; } static inline void as3525_dbop_init(void) { CGU_DBOP = (1<<3) | AS3525_DBOP_DIV; DBOP_TIMPOL_01 = 0xe167e167; DBOP_TIMPOL_23 = 0xe167006e; DBOP_CTRL = 0x40008; GPIOB_AFSEL = 0xc; GPIOC_AFSEL = 0xff; DBOP_TIMPOL_23 = 0x6006e; DBOP_CTRL = 0x52008; DBOP_TIMPOL_01 = 0x6e167; DBOP_TIMPOL_23 = 0xa167e06f; lcd_delay(20); } #endif /* LCD init */ void lcd_init_device(void) { #if defined(SANSA_C200) c200v1_lcd_init(); #elif defined(SANSA_C200V2) as3525_dbop_init(); /* reset lcd */ GPIOB_DIR |= (1<<6); GPIOB_PIN(6) = 0; /* pull reset low */ lcd_delay(20); GPIOB_PIN(6) = 1<<6; /* release reset */ lcd_delay(20); #endif lcd_send_command(R_STANDBY_OFF, 0); lcd_delay(20); lcd_send_command(R_OSCILLATION_MODE, 0x01); lcd_delay(20); lcd_send_command(R_DCDC_AMP_ONOFF, 0x01); lcd_delay(20); lcd_send_command(R_DCDC_AMP_ONOFF, 0x09); lcd_delay(20); lcd_send_command(R_DCDC_AMP_ONOFF, 0x0b); lcd_delay(20); lcd_send_command(R_DCDC_AMP_ONOFF, 0x0f); lcd_delay(20); lcd_send_command(R_DRIVER_OUTPUT_MODE, 0x07); lcd_send_command(R_DCDC_SET, 0x03); lcd_send_command(R_DCDC_CLOCK_DIV, 0x03); lcd_send_command(R_TEMP_COMPENSATION, 0x01); lcd_send_command(R_CONTRAST_CONTROL1, 0x55); lcd_send_command(R_ADDRESSING_MODE, 0x10); lcd_send_command(R_ROW_VECTOR_MODE, 0x0e); lcd_send_command(R_N_LINE_INVERSION, 0x0d); lcd_send_command(R_FRAME_FREQ_CONTROL, 0); lcd_send_command(R_ENTRY_MODE, 0x82); /* vertical dimensions */ lcd_send_command(R_Y_ADDR_AREA, 0x1a); /* y1 + 0x1a */ lcd_send_command(LCD_HEIGHT - 1 + 0x1a, 0); /* y2 + 0x1a */ /* horizontal dimensions */ lcd_send_command(R_X_ADDR_AREA, 0); /* x1 */ lcd_send_command(LCD_WIDTH - 1, 0); /* x2 */ lcd_delay(100); lcd_send_command(R_DISPLAY_ON, 0); } /*** hardware configuration ***/ int lcd_default_contrast(void) { return DEFAULT_CONTRAST_SETTING; } void lcd_set_contrast(int val) { lcd_send_command(R_CONTRAST_CONTROL1, val); } void lcd_set_invert_display(bool yesno) { #ifdef HAVE_LCD_INVERT lcd_send_command(R_SPEC_DISPLAY_PATTERN, yesno ? 1 : 0); #else (void)yesno; #endif } #if defined(HAVE_LCD_ENABLE) void lcd_enable(bool yesno) { if (yesno == is_lcd_enabled) return; if ((is_lcd_enabled = yesno)) { lcd_send_command(R_STANDBY_OFF, 0); lcd_send_command(R_DISPLAY_ON, 0); send_event(LCD_EVENT_ACTIVATION, NULL); } else { lcd_send_command(R_STANDBY_ON, 0); } } #endif #if defined(HAVE_LCD_ENABLE) || defined(HAVE_LCD_SLEEP) bool lcd_active(void) { return is_lcd_enabled; } #endif /* turn the display upside down (call lcd_update() afterwards) */ void lcd_set_flip(bool yesno) { lcd_send_command(R_DRIVER_OUTPUT_MODE, yesno ? 0x02 : 0x07); } /*** update functions ***/ #if MEMORYSIZE > 2 /* not for C200V2 */ void lcd_yuv_set_options(unsigned options) { lcd_yuv_options = options; } /* Line write helper function for lcd_yuv_blit. Write two lines of yuv420. */ extern void lcd_write_yuv420_lines(unsigned char const * const src[3], int width, int stride); extern void lcd_write_yuv420_lines_odither(unsigned char const * const src[3], int width, int stride, int x_screen, /* To align dither pattern */ int y_screen); /* Performance function to blit a YUV bitmap directly to the LCD */ void lcd_blit_yuv(unsigned char * const src[3], int src_x, int src_y, int stride, int x, int y, int width, int height) { unsigned char const * yuv_src[3]; off_t z; /* Sorry, but width and height must be >= 2 or else */ width &= ~1; height >>= 1; y += 0x1a; z = stride*src_y; yuv_src[0] = src[0] + z + src_x; yuv_src[1] = src[1] + (z >> 2) + (src_x >> 1); yuv_src[2] = src[2] + (yuv_src[1] - src[1]); lcd_send_command(R_ENTRY_MODE, 0x80); lcd_send_command(R_X_ADDR_AREA, x); lcd_send_command(x + width - 1, 0); if (lcd_yuv_options & LCD_YUV_DITHER) { do { lcd_send_command(R_Y_ADDR_AREA, y); lcd_send_command(y + 1, 0); lcd_write_yuv420_lines_odither(yuv_src, width, stride, x, y); yuv_src[0] += stride << 1; /* Skip down two luma lines */ yuv_src[1] += stride >> 1; /* Skip down one chroma line */ yuv_src[2] += stride >> 1; y += 2; } while (--height > 0); } else { do { lcd_send_command(R_Y_ADDR_AREA, y); lcd_send_command(y + 1, 0); lcd_write_yuv420_lines(yuv_src, width, stride); yuv_src[0] += stride << 1; /* Skip down two luma lines */ yuv_src[1] += stride >> 1; /* Skip down one chroma line */ yuv_src[2] += stride >> 1; y += 2; } while (--height > 0); } } #endif /* MEMORYSIZE > 2 */ /* Update the display. This must be called after all other LCD functions that change the display. */ void lcd_update(void) { lcd_update_rect(0, 0, LCD_WIDTH, LCD_HEIGHT); } /* Update a fraction of the display. */ void lcd_update_rect(int x, int y, int width, int height) { const fb_data *addr; if (x + width >= LCD_WIDTH) width = LCD_WIDTH - x; if (y + height >= LCD_HEIGHT) height = LCD_HEIGHT - y; if ((width <= 0) || (height <= 0)) return; /* Nothing left to do. */ addr = &lcd_framebuffer[y][x]; if (width <= 1) { /* The X end address must be larger than the X start address, so we * switch to vertical mode for single column updates and set the * window width to 2 */ lcd_send_command(R_ENTRY_MODE, 0x80); lcd_send_command(R_X_ADDR_AREA, x); lcd_send_command(x + 1, 0); } else { lcd_send_command(R_ENTRY_MODE, 0x82); lcd_send_command(R_X_ADDR_AREA, x); lcd_send_command(x + width - 1, 0); } lcd_send_command(R_Y_ADDR_AREA, y + 0x1a); lcd_send_command(y + height - 1 + 0x1a, 0); do { lcd_write_data(addr, width); addr += LCD_WIDTH; } while (--height > 0); }