/*************************************************************************** * __________ __ ___. * Open \______ \ ____ ____ | | _\_ |__ _______ ___ * Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ / * Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < < * Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \ * \/ \/ \/ \/ \/ * $Id$ * * Copyright (C) 2008 by Mark Arigo * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * as published by the Free Software Foundation; either version 2 * of the License, or (at your option) any later version. * * This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY * KIND, either express or implied. * ****************************************************************************/ #include "config.h" #include "cpu.h" #include "lcd.h" #include "kernel.h" #include "system.h" /* Settings to remember when display is turned off */ static bool invert; static bool flip; static int contrast; static bool power_on; static bool display_on; /* Forward declarations */ #if defined(HAVE_LCD_ENABLE) || defined(HAVE_LCD_SLEEP) static void lcd_display_off(void); #endif /* The SA9200 controller closely matches the register defines for the Samsung S6D0151 */ #define R_START_OSC 0x00 #define R_DRV_OUTPUT_CONTROL 0x01 #define R_INVERSION_CONTROL 0x02 #define R_ENTRY_MODE 0x03 #define R_DISP_CONTROL 0x07 #define R_BLANK_PERIOD_CONTROL 0x08 #define R_FRAME_CYCLE_CONTROL 0x0b #define R_EXT_INTERFACE_CONTROL 0x0c #define R_POWER_CONTROL1 0x10 #define R_GAMMA_CONTROL1 0x11 #define R_POWER_CONTROL2 0x12 #define R_POWER_CONTROL3 0x13 #define R_POWER_CONTROL4 0x14 #define R_RAM_ADDR_SET 0x21 #define R_WRITE_DATA_2_GRAM 0x22 #define R_RAM_READ_DATA 0x22 #define R_GAMMA_FINE_ADJ_POS1 0x30 #define R_GAMMA_FINE_ADJ_POS2 0x31 #define R_GAMMA_FINE_ADJ_POS3 0x32 #define R_GAMMA_GRAD_ADJ_POS 0x33 #define R_GAMMA_FINE_ADJ_NEG1 0x34 #define R_GAMMA_FINE_ADJ_NEG2 0x35 #define R_GAMMA_FINE_ADJ_NEG3 0x36 #define R_GAMMA_GRAD_ADJ_NEG 0x37 #define R_GAMMA_CONTROL3 0x38 #define R_GATE_SCAN_START_POS 0x40 #define R_1ST_SCR_DRV_POS 0x42 #define R_2ND_SCR_DRV_POS 0x43 #define R_HORIZ_RAM_ADDR_POS 0x44 #define R_VERT_RAM_ADDR_POS 0x45 #define R_OSC_CONTROL 0x61 #define R_LOW_POWER_MODE 0x69 #define R_PRE_DRIVING_PERIOD 0x70 #define R_GATE_OUT_PERIOD_CTRL 0x71 #define R_SOFTWARE_RESET 0x72 /* Display status */ static unsigned lcd_yuv_options SHAREDBSS_ATTR = 0; /* wait for LCD */ static inline void lcd_wait_write(void) { while (LCD1_CONTROL & LCD1_BUSY_MASK); } /* send LCD data */ static void lcd_send_data(unsigned data) { lcd_wait_write(); LCD1_DATA = data >> 8; lcd_wait_write(); LCD1_DATA = data & 0xff; } /* send LCD command */ static void lcd_send_command(unsigned cmd) { lcd_wait_write(); LCD1_CMD = cmd >> 8; lcd_wait_write(); LCD1_CMD = cmd & 0xff; } static void lcd_write_reg(unsigned reg, unsigned data) { lcd_send_command(reg); lcd_send_data(data); } /* LCD init */ void lcd_init_device(void) { #if 0 /* This is done by the OF bootloader, no need to redo */ DEV_INIT1 &= ~0x3000; DEV_INIT1 = DEV_INIT1; DEV_INIT2 &= ~0x400; LCD1_CONTROL = 0x4680; udelay(1500); LCD1_CONTROL = 0x4684; outl(1, 0x70003018); LCD1_CONTROL &= ~0x200; LCD1_CONTROL &= ~0x800; LCD1_CONTROL &= ~0x400; udelay(30000); #endif power_on = true; display_on = true; invert = false; flip = false; contrast = DEFAULT_CONTRAST_SETTING; } #ifdef HAVE_LCD_SLEEP static void lcd_power_on(void) { LCD1_CONTROL |= 0x1; /** Power ON Sequence **/ /* Start Oscillation */ lcd_write_reg(R_START_OSC, 0x0001); sleep(HZ/20); /* 50ms or more */ /* DSTB=0, SAP2-0=001, BT2-0=101, DC2-0=000, AP2-0=001, SLP=0, STB=0 */ lcd_write_reg(R_POWER_CONTROL1, 0x0d04); /* VR1C=0, VRN14-10=10111, VRP14-10=11111 */ lcd_write_reg(R_GAMMA_CONTROL1, 0x171f); /* SVC3-0=0000, VRH5-4=01 */ lcd_write_reg(R_POWER_CONTROL2, 0x0001); /* VCMR=1, PON=0, VRH3-0=1101 */ lcd_write_reg(R_POWER_CONTROL3, 0x080d); /* VDV6-0=0000100, VCOMG=0, VCM6-0=xxxxxxx */ lcd_write_reg(R_POWER_CONTROL4, 0x0400 | contrast); /* DSTB=0, SAP2-0=010, BT2-0=010, DC2-0=000, AP2-0=010, SLP=0, STB=0 */ lcd_write_reg(R_POWER_CONTROL1, 0x1208); sleep(HZ/20); /* 50ms or more */ /* VCMR=1, PON=1, VRH3-0=1100 */ lcd_write_reg(R_POWER_CONTROL3, 0x081c); sleep(HZ/20); /* OF bootlaoder uses 200ms, no delay in OF firmware */ /* Instructions for other mode settings (in register order). */ lcd_write_reg(R_DRV_OUTPUT_CONTROL, flip ? 0x090c : 0x0a0c); /* FL1-0=10, FDL=0 */ lcd_write_reg(R_INVERSION_CONTROL, 0x0200); /* BGR=1, MDT1-0=00, I/D1-0=11, AM=0 */ lcd_write_reg(R_ENTRY_MODE, 0x1030); /* PT1-0=00, SPT=0, GON=0, DTE=0, CL=0, REV=1, D1-0=01 */ lcd_write_reg(R_DISP_CONTROL, 0x0005); /* FP3-0=0011, BT3-0=1010 */ lcd_write_reg(R_BLANK_PERIOD_CONTROL, 0x030a); /* DIV1-0=00, RTN3-0=0000 */ lcd_write_reg(R_FRAME_CYCLE_CONTROL, 0x0000); /* RM=0, DM1-0=00, RIM1-0=00 */ lcd_write_reg(R_EXT_INTERFACE_CONTROL, 0x0000); /* PKP1=0x0, PKP0=0x0 */ lcd_write_reg(R_GAMMA_FINE_ADJ_POS1, 0x0000); /* PKP3=0x2, PKP2=0x4 */ lcd_write_reg(R_GAMMA_FINE_ADJ_POS2, 0x0204); /* PKP5=0x0, PKP4=0x1 */ lcd_write_reg(R_GAMMA_FINE_ADJ_POS3, 0x0001); /* PRP1=0x6, PRP0=0x0 */ lcd_write_reg(R_GAMMA_GRAD_ADJ_POS, 0x0600); /* PKN1=0x6, PKN0=0x7 */ lcd_write_reg(R_GAMMA_FINE_ADJ_NEG1, 0x0607); /* PKN3=0x3, PKN2=0x5 */ lcd_write_reg(R_GAMMA_FINE_ADJ_NEG2, 0x0305); /* PKN5=0x7, PKN4=0x7 */ lcd_write_reg(R_GAMMA_FINE_ADJ_NEG3, 0x0707); /* PRN1=0x0, PRN0=0x6 */ lcd_write_reg(R_GAMMA_GRAD_ADJ_NEG, 0x0006); /* VRN0=0x4, VRP=0x0 */ lcd_write_reg(R_GAMMA_CONTROL3, 0x0400); /* SCN=0x0 */ lcd_write_reg(R_GATE_SCAN_START_POS, 0x0000); /* SE1=LCD_HEIGHT-1, SS1=0x0 */ lcd_write_reg(R_1ST_SCR_DRV_POS, 0x9f00); /* SE2=0x0, SS2=0x0 */ lcd_write_reg(R_2ND_SCR_DRV_POS, 0x0000); /* HEA=LCD_WIDTH-1, HSA=0x0 */ lcd_write_reg(R_HORIZ_RAM_ADDR_POS, 0x7f00); /* VEA=LCD_HEIGHT-1, VSA=0x0 */ lcd_write_reg(R_VERT_RAM_ADDR_POS, 0x9f00); /* Unknown registers */ lcd_write_reg(0x00a8, 0x0125); lcd_write_reg(0x00a9, 0x0014); lcd_write_reg(0x00a7, 0x0022); power_on = true; } static void lcd_power_off(void) { /* Display must be off first */ if (display_on) lcd_display_off(); power_on = false; /** Power OFF sequence **/ /* DSTB=0, SAP2-0=000, BT2-0=001, DC2-0=000, AP2-0=000, SLP=0, STB=0 */ lcd_write_reg(R_POWER_CONTROL1, 0x0100); /* VCMR=1, PON=0, VRH3-0=1101 */ lcd_write_reg(R_POWER_CONTROL3, 0x080d); } void lcd_sleep(void) { if (power_on) lcd_power_off(); /* Set standby mode */ /* PT1-0=00, SPT=0, GON=1, DTE=1, CL=0, REV=1, D1-0=10 */ lcd_write_reg(R_DISP_CONTROL, 0x0036); /* DSTB=0, SAP2-0=000, BT2-0=101, DC2-0=000, AP2-0=000, SLP=0, STB=1 */ lcd_write_reg(R_POWER_CONTROL1, 0x0501); LCD1_CONTROL &= ~0xffff0001; } #endif #if defined(HAVE_LCD_ENABLE) || defined(HAVE_LCD_SLEEP) static void lcd_display_off(void) { display_on = false; /** Display OFF sequence **/ /* PT1-0=10, SPT=0, GON=1, DTE=1, CL=0, REV=1, D1-0=10 */ lcd_write_reg(R_DISP_CONTROL, 0x1036); sleep(HZ/25); /* 2 or more frames */ /* PT1-0=10, SPT=0, GON=1, DTE=0, CL=0, REV=1, D1-0=00 */ lcd_write_reg(R_DISP_CONTROL, 0x1034); sleep(HZ/500); /* 1ms or more */ /* PT1-0=10, SPT=0, GON=0, DTE=0, CL=0, REV=1, D1-0=00 */ lcd_write_reg(R_DISP_CONTROL, 0x1004); sleep(HZ/25); /* 2 or more frames */ } #endif #if defined(HAVE_LCD_ENABLE) static void lcd_display_on(void) { /* Be sure power is on first */ if (!power_on) lcd_power_on(); /** Display ON Sequence **/ /* PT1-0=00, SPT=0, GON=1, DTE=0, CL=0, REV=0, D1-0=01 */ lcd_write_reg(R_DISP_CONTROL, 0x0021); sleep(HZ/500); /* 1ms or more */ /* PT1-0=00, SPT=0, GON=1, DTE=0, CL=0, REV=0, D1-0=11 */ lcd_write_reg(R_DISP_CONTROL, 0x0023); sleep(HZ/25); /* 2 or more frames */ /* PT1-0=10, SPT=0, GON=1, DTE=1, CL=0, REV=x, D1-0=11 */ lcd_write_reg(R_DISP_CONTROL, invert ? 0x1033 : 0x1037); display_on = true; } void lcd_enable(bool on) { if (on == display_on) return; if (on) { lcd_display_on(); /* Probably out of sync and we don't wanna pepper the code with lcd_update() calls for this. */ lcd_update(); lcd_activation_call_hook(); } else { lcd_display_off(); } } #endif #if defined(HAVE_LCD_ENABLE) || defined(HAVE_LCD_SLEEP) bool lcd_active(void) { return display_on; } #endif /*** hardware configuration ***/ int lcd_default_contrast(void) { return DEFAULT_CONTRAST_SETTING; } void lcd_set_contrast(int val) { contrast = val & 0x7f; if (!display_on) return; /* VDV6-0=0000100, VCOMG=0, VCM6-0=xxxxxxx */ lcd_write_reg(R_POWER_CONTROL4, 0x0400 | contrast); } void lcd_set_invert_display(bool yesno) { invert = yesno; if (!display_on) return; /* PT1-0=10, SPT=0, GON=1, DTE=1, CL=0, REV=x, D1-0=11 */ lcd_write_reg(R_DISP_CONTROL, invert ? 0x1033 : 0x1037); } /* turn the display upside down (call lcd_update() afterwards) */ void lcd_set_flip(bool yesno) { flip = yesno; if (!display_on) return; /* DPL=0, EPL=1, SM=0, GS=x, SS=x, NL4-0=01100 */ lcd_write_reg(R_DRV_OUTPUT_CONTROL, flip ? 0x090c : 0x0a0c); } void lcd_yuv_set_options(unsigned options) { lcd_yuv_options = options; } /* Performance function to blit a YUV bitmap directly to the LCD */ void lcd_blit_yuv(unsigned char * const src[3], int src_x, int src_y, int stride, int x, int y, int width, int height) { (void)src; (void)src_x; (void)src_y; (void)stride; (void)x; (void)y; (void)width; (void)height; } /* Update the display. This must be called after all other LCD functions that change the display. */ void lcd_update(void) { lcd_update_rect(0, 0, LCD_WIDTH, LCD_HEIGHT); } /* Update a fraction of the display. */ void lcd_update_rect(int x, int y, int width, int height) { const fb_data *addr; if (!display_on) return; if (x + width > LCD_WIDTH) width = LCD_WIDTH - x; if (y + height > LCD_HEIGHT) height = LCD_HEIGHT - y; if ((width <= 0) || (height <= 0)) return; /* Nothing left to do. */ addr = &lcd_framebuffer[y][x]; lcd_write_reg(R_HORIZ_RAM_ADDR_POS, ((x + width - 1) << 8) | x); lcd_write_reg(R_VERT_RAM_ADDR_POS, ((y + height -1) << 8) | y); lcd_write_reg(R_RAM_ADDR_SET, ((y & 0xff) << 8) | (x & 0xff)); lcd_send_command(R_WRITE_DATA_2_GRAM); do { int w = width; do { lcd_send_data(*addr++); } while (--w > 0); addr += LCD_WIDTH - width; } while (--height > 0); }