/*************************************************************************** * __________ __ ___. * Open \______ \ ____ ____ | | _\_ |__ _______ ___ * Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ / * Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < < * Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \ * \/ \/ \/ \/ \/ * $Id$ * * Copyright (C) 2005 by Andy Young * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * as published by the Free Software Foundation; either version 2 * of the License, or (at your option) any later version. * * This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY * KIND, either express or implied. * ****************************************************************************/ #include #include "config.h" #include "logf.h" #include "system.h" #include "audio.h" #include "debug.h" #include "udacodec.h" #include "audiohw.h" /* The UDA1380 requires a clock signal at a multiple of the sample rate (256Fs, 384Fs, 512Fs or 768Fs, where Fs = sample rate). Some targets are able to supply this clock directly to the SYSCLK input. The H100 and H300 coldfire targets are limited in the selection of frequencies for this clock signal so they use a PLL inside the UDA1380 (called the WSPLL) to regenerate it from the LRCK signal off the IIS bus. */ #if defined(IRIVER_H100_SERIES) || defined(IRIVER_H300_SERIES) #define USE_WSPLL #endif const struct sound_settings_info audiohw_settings[] = { [SOUND_VOLUME] = {"dB", 0, 1, -84, 0, -25}, [SOUND_BASS] = {"dB", 0, 2, 0, 24, 0}, [SOUND_TREBLE] = {"dB", 0, 2, 0, 6, 0}, [SOUND_BALANCE] = {"%", 0, 1,-100, 100, 0}, [SOUND_CHANNELS] = {"", 0, 1, 0, 5, 0}, [SOUND_STEREO_WIDTH] = {"%", 0, 5, 0, 250, 100}, #ifdef HAVE_RECORDING [SOUND_LEFT_GAIN] = {"dB", 1, 1,-128, 96, 0}, [SOUND_RIGHT_GAIN] = {"dB", 1, 1,-128, 96, 0}, [SOUND_MIC_GAIN] = {"dB", 1, 1,-128, 108, 16}, #endif }; /* convert tenth of dB volume (-840..0) to master volume register value */ int tenthdb2master(int db) { if (db < -720) /* 1.5 dB steps */ return (2940 - db) / 15; else if (db < -660) /* 0.75 dB steps */ return (1110 - db) * 2 / 15; else if (db < -520) /* 0.5 dB steps */ return (520 - db) / 5; else /* 0.25 dB steps */ return -db * 2 / 5; } /* convert tenth of dB volume (-780..0) to mixer volume register value */ int tenthdb2mixer(int db) { if (db < -660) /* 1.5 dB steps */ return (2640 - db) / 15; else if (db < -600) /* 0.75 dB steps */ return (990 - db) * 2 / 15; else if (db < -460) /* 0.5 dB steps */ return (460 - db) / 5; else /* 0.25 dB steps */ return -db * 2 / 5; } /* ------------------------------------------------- */ /* Local functions and variables */ /* ------------------------------------------------- */ static int uda1380_write_reg(unsigned char reg, unsigned short value); unsigned short uda1380_regs[0x30]; short recgain_mic; short recgain_line; /* Definition of a playback configuration to start with */ #define NUM_DEFAULT_REGS 13 unsigned short uda1380_defaults[2*NUM_DEFAULT_REGS] = { REG_0, EN_DAC | EN_INT | EN_DEC | #ifdef USE_WSPLL ADC_CLK | DAC_CLK | WSPLL_25_50 | #endif SYSCLK_256FS, REG_I2S, I2S_IFMT_IIS, REG_PWR, PON_PLL | PON_BIAS, /* PON_HP & PON_DAC is enabled later */ REG_AMIX, AMIX_RIGHT(0x3f) | AMIX_LEFT(0x3f), /* 00=max, 3f=mute */ REG_MASTER_VOL, MASTER_VOL_LEFT(0x20) | MASTER_VOL_RIGHT(0x20), /* 00=max, ff=mute */ REG_MIX_VOL, MIX_VOL_CH_1(0) | MIX_VOL_CH_2(0xff), /* 00=max, ff=mute */ REG_EQ, EQ_MODE_MAX, /* Bass and treble = 0 dB */ REG_MUTE, MUTE_MASTER | MUTE_CH2, /* Mute everything to start with */ REG_MIX_CTL, MIX_CTL_MIX, /* Enable mixer */ REG_DEC_VOL, 0, REG_PGA, MUTE_ADC, REG_ADC, SKIP_DCFIL, REG_AGC, 0 }; /* Returns 0 if register was written or -1 if write failed */ static int uda1380_write_reg(unsigned char reg, unsigned short value) { if (udacodec_write(reg, value) < 0) { DEBUGF("uda1380 error reg=0x%x", reg); return -1; } uda1380_regs[reg] = value; return 0; } /** * Sets left and right master volume (0(max) to 252(muted)) */ void audiohw_set_master_vol(int vol_l, int vol_r) { uda1380_write_reg(REG_MASTER_VOL, MASTER_VOL_LEFT(vol_l) | MASTER_VOL_RIGHT(vol_r)); } /** * Sets mixer volume for both channels (0(max) to 228(muted)) */ void audiohw_set_mixer_vol(int channel1, int channel2) { uda1380_write_reg(REG_MIX_VOL, MIX_VOL_CH_1(channel1) | MIX_VOL_CH_2(channel2)); } /** * Sets the bass value (0-12) */ void audiohw_set_bass(int value) { uda1380_write_reg(REG_EQ, (uda1380_regs[REG_EQ] & ~BASS_MASK) | BASSL(value) | BASSR(value)); } /** * Sets the treble value (0-3) */ void audiohw_set_treble(int value) { uda1380_write_reg(REG_EQ, (uda1380_regs[REG_EQ] & ~TREBLE_MASK) | TREBLEL(value) | TREBLER(value)); } static void audiohw_mute(bool mute) { unsigned int value = uda1380_regs[REG_MUTE]; if (mute) value = value | MUTE_MASTER; else value = value & ~MUTE_MASTER; uda1380_write_reg(REG_MUTE, value); } /* Returns 0 if successful or -1 if some register failed */ static int audiohw_set_regs(void) { int i; memset(uda1380_regs, 0, sizeof(uda1380_regs)); /* Initialize all registers */ for (i=0; i= HW_NUM_FREQ) fsel = HW_FREQ_DEFAULT; ent = values_reg[fsel]; /* Set WSPLL input frequency range or SYSCLK divider */ uda1380_regs[REG_0] &= ~0xf; uda1380_write_reg(REG_0, uda1380_regs[REG_0] | ent[1]); /* Choose 3rd order or 5th order noise shaper */ uda1380_regs[REG_MIX_CTL] &= ~MIX_CTL_SEL_NS; uda1380_write_reg(REG_MIX_CTL, uda1380_regs[REG_MIX_CTL] | ent[0]); } /* Initialize UDA1380 codec with default register values (uda1380_defaults) */ void audiohw_init(void) { recgain_mic = 0; recgain_line = 0; udacodec_reset(); if (audiohw_set_regs() == -1) { /* this shoud never (!) happen. */ logf("uda1380: audiohw_init failed"); } } void audiohw_postinit(void) { /* Sleep a while so the power can stabilize (especially a long delay is needed for the line out connector). */ sleep(HZ); /* Power on FSDAC and HP amp. */ uda1380_write_reg(REG_PWR, uda1380_regs[REG_PWR] | PON_DAC | PON_HP); /* UDA1380: Unmute the master channel (DAC should be at zero point now). */ audiohw_mute(false); } void audiohw_set_prescaler(int val) { audiohw_set_mixer_vol(tenthdb2mixer(-val), tenthdb2mixer(-val)); } /* Nice shutdown of UDA1380 codec */ void audiohw_close(void) { /* First enable mute and sleep a while */ uda1380_write_reg(REG_MUTE, MUTE_MASTER); sleep(HZ/8); /* Then power off the rest of the chip */ uda1380_write_reg(REG_PWR, 0); uda1380_write_reg(REG_0, 0); /* Disable codec */ } /** * Calling this function enables the UDA1380 to send * sound samples over the I2S bus, which is connected * to the processor's IIS1 interface. * * source_mic: true=record from microphone, false=record from line-in (or radio) */ void audiohw_enable_recording(bool source_mic) { #ifdef USE_WSPLL uda1380_regs[REG_0] &= ~(ADC_CLK | DAC_CLK); #endif uda1380_write_reg(REG_0, uda1380_regs[REG_0] | EN_ADC); if (source_mic) { /* VGA_GAIN: 0=0 dB, F=30dB */ /* Output of left ADC is fed into right bitstream */ uda1380_regs[REG_PWR] &= ~(PON_PGAR | PON_ADCR); uda1380_write_reg(REG_PWR, uda1380_regs[REG_PWR] | PON_LNA | PON_ADCL); uda1380_regs[REG_ADC] &= ~SKIP_DCFIL; uda1380_write_reg(REG_ADC, (uda1380_regs[REG_ADC] & VGA_GAIN_MASK) | SEL_LNA | SEL_MIC | EN_DCFIL); uda1380_write_reg(REG_PGA, 0); } else { /* PGA_GAIN: 0=0 dB, F=24dB */ uda1380_regs[REG_PWR] &= ~PON_LNA; uda1380_write_reg(REG_PWR, uda1380_regs[REG_PWR] | PON_PGAL | PON_ADCL | PON_PGAR | PON_ADCR); uda1380_write_reg(REG_ADC, EN_DCFIL); uda1380_write_reg(REG_PGA, uda1380_regs[REG_PGA] & PGA_GAIN_MASK); } sleep(HZ/8); uda1380_write_reg(REG_I2S, uda1380_regs[REG_I2S] | I2S_MODE_MASTER); uda1380_write_reg(REG_MIX_CTL, MIX_MODE(1)); } /** * Stop sending samples on the I2S bus */ void audiohw_disable_recording(void) { uda1380_write_reg(REG_PGA, MUTE_ADC); sleep(HZ/8); uda1380_write_reg(REG_I2S, I2S_IFMT_IIS); uda1380_regs[REG_PWR] &= ~(PON_LNA | PON_ADCL | PON_ADCR | PON_PGAL | PON_PGAR); uda1380_write_reg(REG_PWR, uda1380_regs[REG_PWR]); uda1380_regs[REG_0] &= ~EN_ADC; #ifdef USE_WSPLL uda1380_write_reg(REG_0, uda1380_regs[REG_0] | ADC_CLK | DAC_CLK); #endif uda1380_write_reg(REG_ADC, SKIP_DCFIL); } /** * Set recording gain and volume * * type: params: ranges: * AUDIO_GAIN_MIC: left -128 .. 108 -> -64 .. 54 dB gain * AUDIO_GAIN_LINEIN left & right -128 .. 96 -> -64 .. 48 dB gain * * Note: - For all types the value 0 gives 0 dB gain. * - order of setting both values determines if the small glitch will be a peak or a dip. The small glitch is caused by the time between setting the two gains */ void audiohw_set_recvol(int left, int right, int type) { int left_ag, right_ag; switch (type) { case AUDIO_GAIN_MIC: left_ag = MIN(MAX(0, left / 4), 15); left -= left_ag * 4; if(left < recgain_mic) { uda1380_write_reg(REG_DEC_VOL, DEC_VOLL(left) | DEC_VOLR(left)); uda1380_write_reg(REG_ADC, (uda1380_regs[REG_ADC] & ~VGA_GAIN_MASK) | VGA_GAIN(left_ag)); } else { uda1380_write_reg(REG_ADC, (uda1380_regs[REG_ADC] & ~VGA_GAIN_MASK) | VGA_GAIN(left_ag)); uda1380_write_reg(REG_DEC_VOL, DEC_VOLL(left) | DEC_VOLR(left)); } recgain_mic = left; logf("Mic: %dA/%dD", left_ag, left); break; case AUDIO_GAIN_LINEIN: left_ag = MIN(MAX(0, left / 6), 8); left -= left_ag * 6; right_ag = MIN(MAX(0, right / 6), 8); right -= right_ag * 6; if(left < recgain_line) { /* for this order we can combine both registers, making the glitch even smaller */ unsigned short value_dec; unsigned short value_pga; value_dec = DEC_VOLL(left) | DEC_VOLR(right); value_pga = (uda1380_regs[REG_PGA] & ~PGA_GAIN_MASK) | PGA_GAINL(left_ag) | PGA_GAINR(right_ag); if (udacodec_write2(REG_DEC_VOL, value_dec, value_pga) < 0) { DEBUGF("uda1380 error reg=combi rec gain"); } else { uda1380_regs[REG_DEC_VOL] = value_dec; uda1380_regs[REG_PGA] = value_pga; } } else { uda1380_write_reg(REG_PGA, (uda1380_regs[REG_PGA] & ~PGA_GAIN_MASK) | PGA_GAINL(left_ag) | PGA_GAINR(right_ag)); uda1380_write_reg(REG_DEC_VOL, DEC_VOLL(left) | DEC_VOLR(right)); } recgain_line = left; logf("Line L: %dA/%dD", left_ag, left); logf("Line R: %dA/%dD", right_ag, right); break; } } /** * Enable or disable recording monitor (so one can listen to the recording) * */ void audiohw_set_monitor(bool enable) { if (enable) /* enable channel 2 */ uda1380_write_reg(REG_MUTE, uda1380_regs[REG_MUTE] & ~MUTE_CH2); else /* mute channel 2 */ uda1380_write_reg(REG_MUTE, uda1380_regs[REG_MUTE] | MUTE_CH2); }