Replace inline section copy/fill loops with subroutines, which
reduces code size a bit and and handle zero size copies properly.
Remove the cache initialization loop as well. There's no actual
reason for this because the SPL initializes the caches and just
dropping the cache can even be harmful (in this case it wasn't,
because the SPL flushes the whole cache right before calling in).
Change-Id: I7cddc9ed6d060b1f1bdd75544297883d014cad2d
This is intended for debugging OF kernel boot problems and has
to be enabled manually at compile time to make it usable.
Change-Id: Ie5ce9f0a7639be0acf5e3879cfc3a7b8b89caa5c
Two helpers (_init_clocktree and _init_uart2) already existed in
the SPL and are copied verbatim from there. The SPL versions are
still present and will be removed when dual boot works from the
main bootloader.
The other two helpers (_cleanup and _load_pdma_fw) are new.
Change-Id: I4661667966e26f52e6c5142f1947d2a34b7008ef
On the bootloader there's no point reserving memory for these,
the only users of codecbuf/pluginbuf are in the apps/ tree.
Change-Id: Ib57b4d59aff8f4dcc753d7993956ed15e61cdc52
Using the audio buffer directly is a bad idea because this will
render core_alloc non-functional if load_firmware() writes into
the buffer but then fails, for example on a checksum mismatch.
Change-Id: Ib2d17bcea53bdea1c4c5496cec0c4eee5dd66069
Document what the symbols are supposed to mean, fixup SPL's
usage of DRAM_END which should really be SDRAM_END instead.
No functional changes.
Change-Id: Ie85b0ee35fea8b7858891e5b9d6634eaae42c9f8
The header format is basic, a variable length list of values
tagged by 4-byte strings. The main application to to allow a
loader to determine the load address of the binary at runtime
instead of using a hardcoded address. But the header contents
aren't fixed and it could be extended for other purposes too.
Change-Id: If51d85b4c2eb53c919a91b54985b157e8e5c20ef
This didn't account for partial page reads properly which resulted
in corrupted data. Fortunately, current released bootloaders do not
perform such reads so they don't trigger this bug.
Change-Id: I426a95ef8d0f20f4567498530e216d80e1aceef2
There are various allocations that can't be moved or shrunk.
Provide a global callback struct for this use case instead of
making each caller declare its own dummy struct.
Also fixed ROLO and x1000 installer code which incorrectly
used movable allocations.
Change-Id: I00088396b9826e02e69a4a33477fe1a7816374f1
The OST prescaler bugfix (7a5130a277) broke runtime switching
between 1.0V and 2.0V modes. The 1ms delay after shutting down
the DAC isn't long enough to reset it, so it gets stuck in the
power mode assigned at boot. Change the delay back to 4ms, the
effective value prior to the OST bugfix.
Change-Id: Ic4583d1a6fa82540062aa185386f14bbf785a3f4
Recording works now, although I'm sure there will be a few
things that need fine-tuning. A major issue is that writing
to the SD card creates noticable interference, which happens
on the original firmware too but seems worse under Rockbox.
(Since Rockbox waits until RAM fills up before writing data,
the interference will only be heard on >50 MiB recordings.)
Change-Id: I5561dd9668c3bdd34e92f34ef50848aef8c0b7eb
Define proper symbolic constants for power mode. Also allow
targets to define the default power mode setting.
Change-Id: Ia07cf854dce47d0a6aa88e067471f1ff9fbc45fb
Remove the battery power ADC since it's not used right now,
and seems to fluctuate too rapidly to be of much use.
Change-Id: If115e4e3ce14d4c18ce899f5a889f7f99ab66489
This caused LCD problems on the ErosQ, where the screen would
go white until being put through a sleep/wake cycle. The exact
reason for this isn't obvious, but the problem didn't exist
prior to the AXP driver rewrite.
The two dependent changes,
42999913ba - x1000: Increase USB current limit to 500 mA at all times
90dd2f84a9 - x1000: Correctly limit USB charging current
ended up bringing the USB charging situation back to where it
was prior to the rewrite, so the cleanest option is to revert
the whole lot.
This reverts commit 42999913ba.
This reverts commit 90dd2f84a9.
This reverts commit 2d89143962.
Change-Id: I1cff2bfdd1b189df14bcf8cce42db725caa470d7
The 100 mA USB current limit added in commit 90dd2f84a9
is a problem when booting with a completely dead battery.
Often 100 mA isn't enough to power the player, never mind
charge the battery, so revert to the old behavior of only
limiting charge current.
Given that the original firmware on these devices isn't
following the USB spec to the letter, it's probably not
worth trying to make Rockbox do so unless and until it
causes a real problem - which hasn't happened yet.
Change-Id: I179a08310c226fe01460680c62fd25fd69079256
The way this was done before was wrong - limiting the charge
current is not enough since the device will draw additional
power to run. Use the AXP192's vbus current limit control to
stay compliant with the USB specification.
Change-Id: I91b84e3480a432e49bec53cf2a17e4e3444404a4
I noticed a few mistakes in the old driver code and it was in
need of an overhaul anyway... I decided to scale things back,
simplify the code and remove most of the debug menus, netting
a nice code size savings.
One new feature is an advanced debug menu which is accessible
by recompiling the code with AXP_EXTRA_DEBUG. It adds quite a
bit of code size and isn't useful other than for development
so it must be manually enabled by editing the source.
Change-Id: I30e17c1194c14823decd726a574ed14451d4cb2d
This allows battery run time to be calculated from the
actual battery usage on the FiiO M3K and Shanling Q1.
This isn't very good for the time being and the estimate
tends to go all over the place due to small variations
in current or voltage.
The Eros Q can support this feature as well, but since
it already has fixed estimates defined and the quality
of the "real time" estimate is low I am not enabling it
there.
Change-Id: Id34a93ee4b7d66f9f7e56ef0f5149f67e8e72039
Future-proofing against newer versions of GCC/binutils which
are stricter about the use of 'inline' functions in headers.
Change-Id: Id620812ed340f0d790ba6c5b8b5cb1d700acfbbf
The FT6x06 driver used for the Shanling Q1's touchscreen
has been extended to report more than one touch point. It
can also return the gesture detected by the controller,
but this doesn't seem to report anything useful on the Q1.
Multi-touch is only useful in 3x3 grid mode since the Rockbox
button API cannot report more than one touch point.
The FiiO M3K uses the same driver so it's been updated to the
multi-touch API, but functionality is unchanged.
Change-Id: I4de42f44808d6eb902e3da212d8f936b7a5042c7
All three X1000 native targets turned out to have a very
similar boot configuration and used a nearly identical
makefile. Eliminate this duplication by moving the logic
into the main makefile.
Change-Id: I13044b9675c0abd605b8accdb2fee4f54549b020
Appears to return 0 until the axp has (presumably) completed
its first real measurement.
Note about erosq: keep the power_inint() delay large to ensure
nothing breaks in the bootloader for the time being.
Change-Id: I444e858207cc401c42f1e6ceacf067ad543d4ff8
OST timer fix (7a5130a277) causes a boot failure on some units,
the battery voltage reading needs more time to stabilize.
Change-Id: Ic4a9ba90a16fab8ac6d27dbbe7af381f7c810f8f
The battery stabilization delay call seems to need to be
about 170 at minimum now, let's do 190 for safety (+20ms).
Change-Id: Ifd0248891abe827dfcc3e6baf48cc5bef0d0cc1c
It turns out the prescaler fields in OST_CTRL are 2 bits wide,
not 3. The programming manual (as usual) is ambiguous and its
diagram shows 2-bit wide fields, but the bit positions in the
text give a 3-bit wide field. Ingenic's Linux code and my own
testing shows that they are, in fact, 2 bits wide.
This caused the OST2 divisor to be 16 instead of 4; the OST1
divisor was correct. This means that all udelay/mdelay calls
took 4x longer than they should've. After this change the OST2
prescaler will be 4, as intended, and udelay/mdelay calls will
wait for the intended duration.
Change-Id: I2ac0a9190f49b59a840c649bf586131f5f9fde82
Write -1 to AIC_DR to initialize the "last sample"
to -1 in order to prevent power-on clicks.
It appears necessary to completely fill the FIFO,
otherwise I was able to get a click out of it, however
uncommon it was.
Not only does this prevent a click when first
playing a song after power-on, but it also seems to prevent
any click at all when powering on - previously, a small
click may have been heard when first booting.
Change-Id: I2b81c2fa6af9809ef1c354d7a08ca8f9893a7690
Previously it used the last sample, which turns out to be broken.
The AIC appears to send out a random non-zero sample continously
after boot -- probably because the last sample is uninitialized by
the hardware. Disabling playback is supposed to make it send zero
samples irregardless of the LSMP bit according to the docs, but it
doesn't seem to work this way.
- Change eliminates the white noise heard on the M3K after boot.
- Change has no adverse effects on the Q1.
- Leave Eros Q on the old setting since sending zeros exacerbates
clicking due to DAC's automute feature.
Change-Id: I9996793fc34f4475b19700d076b11505353b3836
Adjust the battery scale to be a little better. I've set
the 100% (discharge) point to be where the battery sags to
when it is done charging but still plugged in.
Not quite sure how best to set the charge scale, it's just
equal to the discharge scale for now.
Change-Id: I9a2730c0b2051300af9eeddb4f67164f38a29002
IMHO the current name is somewhat misleading:
- usb_drv_send() is blocking and we have usb_drv_send_nonblocking()
for the non-blocking case. This inconsistent naming can only
promote confusion. (And what would we call a blocking receive?)
- Other hardware abstraction APIs in Rockbox are usually blocking:
storage, LCD, backlight, audio... in other words, blocking is the
default expected behavior, with non-blocking calls being a rarity.
Change-Id: I05b41088d09eab582697674f4f06fdca0c8950af
