Based on g#844 and g#949, it is intended as a replacement for the
current s3c6400x USB driver.
The DesignWare USB OTG core is integrated into many SoC's, however
HW core version and capabilities (mainly DMA mode, Tx FIFO mode,
FIFO size and number of available IN/OUT endpoins) may differ:
CPU targets HW ver DMA NPTX FIFO FIFO sz #IN/OUT
-------- ------------- ------ --- --------- ------- -------
as3525v2 sansaclipplus 2.60a Yes Dedicated 0x535 4/4
sansaclipv2
sansaclipzip
sansafuzev2
s5l8701 ipodnano2g 2.20a Yes Shared 0x500 4/5
s5l8702 ipod6g 2.60a Yes Dedicated 0x820 7/7
ipodnano3g
s5l8720 ipodnano4g ? ? ? ? ?
Functionality supported by this driver:
- Device mode, compatible with USB 1.1/2.0 hosts.
- Shared FIFO (USB_DW_SHARED_FIFO) or dedicated FIFOs.
- No DMA (USB_DW_ARCH_SLAVE) or internal DMA mode.
- Concurrent transfers: control, bulk (usb_storage, usb_serial) and
interrupt (usb_hid).
Actually this driver is not used by any CPU, it will be enabled for
each individual CPU/target in next patches.
Change-Id: I74a1e836d18927a31f6977d71115fb442477dd5f
Apparently I simply forgot to calibrate it when the port was done and the
current values are just plain wrong, especially for the charging curve.
Change-Id: Ied3cafa52f31f182f953714e28edc4c5e891255f
There are two very suspicious things in the power off code:
- it does not properly unlock the power register, so it should fail (!)
- it does not disable sw/hw watchdog so if register fails, the device will
most probably crash horribly because of the watchdog
I don't even understand how it worked before.
Change-Id: I9f3f94bd012e52c3b50cd5b658d68b5eb907f79b
* Implements RFC 4226 (HOTP) and RFC 6238 (TOTP)
* Adds sha1.c to apps/plugins/lib (orignally tools/hmac-sha1.c)
* See manual entry for more information
Change-Id: Ia4a4031b29f97361b541e71438aa7f3ea82212f2
The old driver was bad in many respect, it had some race conditions, it was
using a thread to serialize transfers because of the legacy i2c interface.
It also had huge latency (typically 50ms but delays up to 300ms can happen),
thus some presses were missed.
The new driver takes advantage of the new i2c driver to do everything
asynchronously. It also does not need a thread anymore because queueing
ensures proper serialization. It provides much better and reliable latency
(typically ~2ms).
Also fix the debug screen which was horribly broken. The new screen also
displays the deadzones.
Change-Id: I69b7f99b75053e6b1d3d56beb4453c004fd2076e
The new driver provides several new features:
- asynchronous transfer
- transactions (several transfers executed at once)
- queueing
The style still provides the legacy interface.
Change-Id: I6d8ecc89d1f7057847c9b2dc69b76cd45c9c8407
* --static-libs isn't supported on some (possibly newer) SDL installs, falls back to --libs if this is the case
Patch mostly by Amaury Pouly.
Change-Id: I6dd2f4847f2a2d1de7b2d287c0af6651cec461ff
Map short menu press to context menu/quickscreen.
Map long menu press to return to main menu.
Also remove some stupid keylock mapping, that doesn't make sense.
Change-Id: I5f9b05af261bcbd2f0cf116f99570c4d853e0394
Always enable support for SET_BLOCK_COUNT on mmc: it is mandatory. For some
reason (probably a mistake) it was disabled unconditionaly on mmc.
Also deselect sd card after init. Although it is unlikely to make a difference,
it is already done for mmc so stay consistent.
Change-Id: I276f0d95f5bb6a0bf431c2fff4589d3dfb15f8c7
The screen currently displays for each device the bus width, set_block_count
support, HS capability and whether it is enabled for not.
Change-Id: I6b1c3b1019e55ef1097a23c1f54fb07f5c7aa3b0
Some players like the ZEN X-Fi have a wide but not tall screen, it is
thus better to display everything on one line for each button
Change-Id: Ided3d4ff689cc5d3bcc2bdba4c7e046cf7dc0954
ffmpeg_bitstream.c is included in libcodec, so there doesn't seem to
be any reason for individual codecs to also compile it (and clobber
any previous copy while they're at it, leading to broken builds)
Change-Id: I2bedc277ab109f44a6e8feb3d12ed01a720e00a6
This screen allows to put the device in a special mode where:
- charging is disabled
- device only draws power from 5V (thus battery is untouched)
This is useful to measure the device consumption by measuring directly
the usb power consumption.
Change-Id: I2716ced0a5bb33c3c9a2607f2d17a0ce02f5689c
Per Freescale recommandation, we need to ramp up the 4.2V rail before enabling
charging. Ramping should be done at 1 step/10ms, but the old code did 1 step/1s
because the powermgmt_step() function is called once every second. Use a tick
task to ramp up much faster.
Change-Id: I9a52bdd0c2ba5426d83ed42db8db7ecce2fea1f7
The old code used button_get() to read the button status and wait for a
key to leave the panic screen. This is broken since when IRQ are disable,
the button mask is not updated anymore for touchpad and adc buttons. For
now, only use pswitch: this should be good enough for all targets.
Change-Id: I0ae179e24555ac20c3d2bf2d267c1bb0e2ceded0
The old timrot setup API was very low-level and unfriendly. The new one
makes in easier to select the frequency source. Use to simplify timer
and kernel timer code.
Change-Id: Iffcdf11c00e925be9ec8d9a4efc74b197b6bd2aa
The adc channel monitored for jack detection does not really have a fixed
value when plugged. Instead use the same logic as the OF and simply use a
threshold.
Change-Id: I1d5270d83eb14decce29a39d8201ea1d1fb4436c
For some reason those targets have quite imprecise button voltages and the
old margin was too small. This should fix the button-not-working issue,
especially when the player is very hot and cold.
Change-Id: I9fcddd7f079cd1c4ee121567fb21a4a0cbc0562b
The current driver is limited to checking if the adc value equals another
one with a hardcoded margin. This commit changes two aspects of that:
- the margin can be changed globally using IMX233_BUTTON_LRADC_MARGIN
and can also be overriden per button using the new LRADC_EX macro
- the lradc logic gained two comparison modes to check if the source
value is greater (or lower) than a threshold.
Change-Id: If1614451dafeae818a96e6f23a84e6731331ba03
Shorten some text to make the text readable in the debug screen of
targets with small LCD (like NWZ-380). In some screens, the only
option is to display less information.
Change-Id: I78f8f35f7c507de19e5d27a918157504155f2ba6
The power management code was erroneously shuting down the 4.2V rail
when charging is complete. This resulted in the DCDC draining the battery
and thus the battery discharging with USB plugged...
The new code keeps the 4.2V rail active so that battery remains untouched
once charge is complete.
Change-Id: I36e8d31e8115c12ce813c939c5d7bbf2c3490157
NOTE: this commit does not introduce any change, ideally even the binary should
be almost the same. I checked the disassembly by hand and there are only a few
differences here and there, mostly the compiler decides to compile very close
expressions slightly differently. I tried to run the new code on several targets
to make sure and saw no difference.
The major syntax changes of the new headers are as follows:
- BF_{WR,SET,CLR} are now superpowerful and allows to set several fileds at once:
BF_WR(reg, field1(value1), field2(value2), ...)
- BF_CS (use like BF_WR) does a write to reg_CLR and then reg_SET instead of RMW
- there is no more need for macros like BF_{WR_,SET,CLR}_V, since one can simply
BF_WR with field_V(name)
- the old BF_SETV macro has no trivial equivalent and is replaced with its
its equivalent for BF_WR(reg_SET, ...)
I also rename the register headers: "regs/regs-x.h" -> "regs/x.h" to avoid the
redundant "regs".
Final note: the registers were generated using the following command:
./headergen_v2 -g imx -o ../../firmware/target/arm/imx233/regs/ desc/regs-stmp3{600,700,780}.xml
Change-Id: I7485e8b4315a0929a8edb63e7fa1edcaa54b1edc
- Speed auto detection is launched when an accessory is inserted,
so the user doesn't need to modify settings to use accessories
that operates at different speeds (or when the same accessory is
unplugged and plugged again).
- UART controller is disabled when no accessory is inserted, not
much powersave but everything counts.
Change-Id: If20c3617c2a87b6277fd7e0270031030c44fa953
Since the stub code is shared with NWZ-360, it enables the pullup for the
hold button, but the NWZ-370/380 doesn't have a hold button so don't compile
this code in, it could potentially have unexpected effets or increase consumption
Change-Id: I28c8aa40fc7f9373593ff105fb6df557a6f57ccd
This change ensures that Sansa Connect bootloader.bin will fit in its flash
partition.
Fix _flash_sizem calculation, division was not working properly because
FLASHSIZE included subtraction and defined value was not in parenthesis.
Prior to this change _flash_sizem was 0x00800000, now it is correctly set
to 4 in case of Sansa Connect and 8 in case of other TMS320DM320 players.
This significantly improves boot time as cache is now enabled only for
real flash memory region.
Change-Id: If3e50a3075c840dcb69dfafe5bba608a0acd2bf8
PMU interrupts are used to detect USB Vbus, wall adaptor, accessories
and holdswitch. A thread is needed to poll the PMU throught I2C, ATM
it does nothing but showing the state of the inputs on the HW debug
menu, funcionallity for each individual input will be added in next
patches.
Change-Id: If93bf2044d1052729237a7fd1431c8493e09f1c7
