NOTE: this commit does not introduce any change, ideally even the binary should
be almost the same. I checked the disassembly by hand and there are only a few
differences here and there, mostly the compiler decides to compile very close
expressions slightly differently. I tried to run the new code on several targets
to make sure and saw no difference.
The major syntax changes of the new headers are as follows:
- BF_{WR,SET,CLR} are now superpowerful and allows to set several fileds at once:
BF_WR(reg, field1(value1), field2(value2), ...)
- BF_CS (use like BF_WR) does a write to reg_CLR and then reg_SET instead of RMW
- there is no more need for macros like BF_{WR_,SET,CLR}_V, since one can simply
BF_WR with field_V(name)
- the old BF_SETV macro has no trivial equivalent and is replaced with its
its equivalent for BF_WR(reg_SET, ...)
I also rename the register headers: "regs/regs-x.h" -> "regs/x.h" to avoid the
redundant "regs".
Final note: the registers were generated using the following command:
./headergen_v2 -g imx -o ../../firmware/target/arm/imx233/regs/ desc/regs-stmp3{600,700,780}.xml
Change-Id: I7485e8b4315a0929a8edb63e7fa1edcaa54b1edc
Using the ssp macros, we can easily handle the stmp3600 which
has a single ssp block. Take care of all the nasty differences
between targets like bus width
Change-Id: If98a091cc262e9e6834f6fb9826f7c5515bfe621
Under some circumstance (timeout), the dma interrupt is not fired
and only the error one is. This can happen with some picky SD
cards and with the current code it causes a 1 second timeout.
This code properly catches the error interrupt to stop as soon
as possible.
Change-Id: I9c53ea272d01793f0f229571502e99eb62f1b723
The clkctrl functions were becoming a mess. Normalise the names,
get rid of the xtal derived as special case and use the same
interface.
Change-Id: Ib954a8d30a6bd691914b5e0d97774ec9fc560c50
A number of pins on the imx233 are standard and manually calling
functions to acquire, set function/drive/output is painful. This
will become unmanageable when we will add support for the other
stmp chips.
Introduce the concept of virtual pin which is a way to completely
describe a virtual pin (virtual because pins are muxed).
Change-Id: I01b6e040945648e58e1d1abab06529c9571c5f10
The current pinctrl functions were a mess. Normalise the functions
names to make them shorter and clearer.
Change-Id: Iac6ff84625ef2b7610268e3a5802dc0088de3167
Because DMA descriptors needs to be committed and discarded from
the cache, if they are not cache aligned and/or if their size
is not a multiple of cache ligne, nasty side effects could occur
with adjacents data. The same applies to DMA buffers which are
still potentially broken. Add a macro to ensure that these
constraints will not break by error in the future.
Change-Id: I1dd69a5a9c29796c156d953eaa57c0d281e79846
The icoll code now has an IRQ storm detection mechanism which
will prevent the device from hard freezing in case it happen.
Change-Id: I9861238dce61d29af1e48f9c534ec63a7f23465c
Past development has proved that one can mistakely use
the same pin for two uses without noticing. Since this
causes extremely hard to find bugs, the infrastructure
will allow to register pin uses and panic when a conflict
is detected. The pinctrl debug now shows the pin uses
when its support is compiled in.
Change-Id: Idb2d5235ce09207d77aa474d6f158e72b933761a
